Yes, ProKure V is the right tool for disinfecting hydroponic trays, propagation trays, flood-and-drain tables, and rolling bench trays between cycles. It is a liquid Hospital-Type disinfectant built on chlorine dioxide (ClO2) chemistry, used on hard, non-porous surfaces at an exposure time of 10 minutes at 100 ppm. Its label kill list covers Fusarium solani (ATCC 36031), the root-zone pathogen that carries over inside a dirty tray. It leaves no residue, so the tray is ready for the next cycle. What it is not: a product you spray on living plants.
Why trays are the between-cycle risk point
A grow room does not fail an Aspergillus or a general mold test because of the air alone. It fails because pathogen load builds on the surfaces that touch the root zone over and over, and the tray is the worst offender. Water sits in it. Roots sit in it. Runoff pools in the drain channel and the return manifold. Between harvests, that tray is the single most reused, most contaminated surface in the room, and it is the one growers clean last and worst.
Fusarium and Pythium load in the root zone
Fusarium and Pythium are the two names that keep a head grower up at night, and both live in exactly the places a tray collects: standing water, old substrate crumbs, biofilm on the plastic. A clone that looked healthy going in can seed the next batch if the tray it sat in never got disinfected. ProKure V matters here because its label fungicide claims name Fusarium solani (ATCC 36031) directly, per the ProKure V product label. That is the specific anchor a general-purpose cleaner cannot give you. When you disinfect the tray, you are breaking the carryover chain before the next crop ever touches the surface.
Biofilm inside drain channels and return manifolds
The part of a tray you cannot see is the part that fails you. Drain channels, ebb-and-flow fittings, and irrigation return lines accumulate biofilm, a slimy matrix that shields microbes from most surface cleaners. This is where chlorine dioxide earns its place. ClO2 is an oxidizer that penetrates biofilm rather than just wiping the top layer, which is the chemistry difference between a product that resets a tray and one that smears the problem around. None of the top-ranking product listings for this search even mention biofilm, let alone the drain-channel geometry where it hides.
The compliance cost of a failed pre-sale test
In most regulated markets, a mature crop cannot be sold until it passes a mandatory microbial test. A positive result on a six-figure harvest is not a cleaning inconvenience, it is a revenue event. Reframe tray sanitation accordingly: the few dollars of disinfectant per turnover is insurance against a batch you cannot sell. That is the Owner and Business Director math, and it is why prevention belongs in the budget as protection, not as a cost line to trim.
What ProKure V is, and what it is not
Sort out the claims before you build a protocol, because the single biggest source of grower confusion is treating a surface disinfectant like a plant spray.
An EPA-registered Hospital-Type disinfectant built on ClO2
ProKure V is a water-activated, liquid chlorine dioxide generating disinfectant. You tear open the foil package, drop the sealed white inner pouch into an opaque container of water (do not open the white pouch), agitate for one minute at 15-minute intervals, and let it reach full strength at one hour. The result is a Hospital-Type disinfectant for hard, non-porous surfaces. The incumbent product pages sell the what without the how for a tray: the top-ranked brand page leads with "Hospital-type disinfectant." and "Kills mold and mildew." but never once connects that to a tray, hydroponics, or a between-cycle workflow.
Kill list highlights, including Fusarium solani (ATCC 36031)
The ProKure V product label documents a disinfectant kill list used at an exposure time of 10 minutes at 100 ppm, and a fungicide claim that names Fusarium solani (ATCC 36031), Botrytis sp. and Penicillium digitatum, and Aspergillus niger. For a tray operator, the Fusarium line is the headline. Every kill claim on this page is drawn from the ProKure V product label; if the label changes, the claim changes with it. See product label for claims, instructions, mixing/dilution, and PPE requirements.
The "hard, non-porous surfaces" restriction, verbatim from the label
ProKure V is for hard, non-porous surfaces: the stainless, glass, vinyl, polypropylene, PVC, and other non-permeable materials that trays are made from. It is not a soil drench for the plant and it is not a foliar product. The brand FAQ states the boundary plainly: ProKure V is approved to use on hard, non-porous surfaces. Honor that line and you stay compliant; blur it and you are using an EPA-registered product inconsistently with its labeling.
"Suitable for use with plants in the room," clarified for tray use
Here is the claim that trips growers up. The ProKure V product listing states "Suitable for use with plants in the room." That is true, and it is a real wedge: it means you can disinfect an empty tray while other plants live elsewhere in the same room, without evacuating the whole crop. It does not mean you spray the solution onto the plants. You clean the hard surface; the plant is never the target. Growers who conflate those two claims are exactly the churn risk Phase 1 flagged, the ones who do not understand what ClO2 actually is. Clarity here is the whole point.
Tray types ProKure V is appropriate for
If the surface is hard and non-porous, ProKure V is on the table. Flood-and-drain (ebb-and-flow) tables, propagation and clone trays, clone-dome bases, rolling bench trays, NFT channels, and the drain manifolds that feed them are all fair game. Rockwool and other substrate residue should be mechanically removed first; you are disinfecting the tray surface, not sterilizing the growing medium. On material compatibility, the one concrete note the competing listings offer is from a storefront product description, which states that ProKure V "can be applied by spraying, pouring, and mopping, and its neutral pH makes it compatible with almost any surface." Neutral pH is why ABS, HDPE, polypropylene, PVC channels, aluminum benches, and stainless steel tolerate repeated cycles without the pitting a harsh acid or chlorine bleach can cause over time. Always confirm an unusual surface against the label before you commit a whole room to it.
Between-cycle tray disinfection SOP
A protocol beats a vibe. None of the top-ranking pages give a tray operator a written, repeatable workflow, so here is the one that matches the label.
Step 1, mechanical debris removal
Pull roots, substrate crumbs, and sediment out of the tray and the drain channel first. A disinfectant works on a visibly clean surface; it is not a substitute for scrubbing off caked debris. Pre-clean visibly soiled surfaces with a non-disinfectant cleaner as needed.
Step 2, activation
Tear open the foil package, remove the white inner pouch, and do not open the white inner pouch. Add the pouch to an opaque (not clear) container filled with the correct amount of water for 100 ppm, agitate for one minute at 15-minute intervals, and allow one hour to reach full strength. Use the activated solution within 15 days.
Step 3, application and contact time
Apply by spraying, pouring, or mopping so the entire tray surface, including the drain channel, is visibly wet. Hold a 10-minute contact time at 100 ppm, the exposure the label specifies to disinfect hard, non-porous surfaces. Do not let the surface dry before the contact time is up.
Step 4, air-dry and residue check
ProKure V leaves no residue, so once the contact time is met and the tray dries, there is nothing to rinse off before the next cycle. Confirm the surface is dry and clean to the eye.
Step 5, documentation for the audit trail
Log the date, the SKU, the dilution, the contact time, and the operator. A multi-state cultivation director standardizing across facilities, and a QA lead facing an inspection, both need the paper trail as much as the clean tray. Keep the ProKure V label and Safety Data Sheet on file with the record.
SKU sizing by facility footprint
Match the packet to the water volume you actually need, because ProKure V is sold by yield.
0.042oz packet, 1 quart
Makes 1 quart of solution. Right for a single-tray touch-up or a small propagation station.
0.17oz packet, 1 gallon
Makes 1 gallon. Suits a small propagation room or a handful of clone trays.
0.84oz packet, 5 gallons
Makes 5 gallons. The workhorse size for a standard flower-room tray turnover.
3.36oz packet, 20 gallons
Makes 20 gallons. Built for multi-room, multi-facility MSO turnover where dozens of flood trays get reset at once. Buy and reorder the SKU that maps to your tray count on shop.groclarity.com.
ProKure V compared with bleach and quats for tray cleaning
This is a category comparison, not a brand fight. Against bleach and quaternary ammonium (quats), ProKure V wins on the axes a tray operator feels every turnover.
Residue and plant re-introduction timing
Bleach and many quats leave a residue that has to be rinsed and that can stress a new crop if the tray is reused too soon. ProKure V leaves no residue, so the tray is ready for the next cycle once it dries. That is the difference between a tray you can turn around in hours and one you have to babysit.
Crew re-entry and PPE
Bleach fumes clear a room and slow a crew down. Follow the ProKure V label for PPE, but the practical read is a faster, less disruptive turnover than a bleach protocol that evacuates the space.
Surface degradation over cycles
Chlorine bleach and strong acids degrade plastics and corrode metal over repeated use. ProKure V's neutral pH is gentler on the ABS, polypropylene, and aluminum that trays are built from, which protects the capital you have sitting in benches and tables.
EPA compliance and label discipline
For a regulated operator, the compliance line is not a footnote, it is the page.
The verbatim federal-law statement
It is a violation of Federal Law to use EPA registered products in a manner inconsistent with the product labeling. Read the entire product label and use strictly in accordance with precautionary statements and use.
Where to find the ProKure V label and SDS
The full ProKure V product label, SKU sheet, and Safety Data Sheet live on prokuresolutions.com. Pull them before an inspection and keep them with your turnover logs so procurement and QA are never scrambling at audit time.
What "hard, non-porous surfaces" means for a tray operator
It means the tray, the channel, the fitting, and the bench, the hard plastic and metal. It does not mean the rockwool, the media, or the plant. Keep the application on the surface and you are inside the label.
When ProKure V is the wrong tool
Use the right product for the job and hand the reader off when V is not it.
Whole-room gas-phase treatment
For sealing an empty room and treating it in the gas phase, that is a ProKure D or ProKure G decision, not a liquid-surface one. ProKure G is a fast-release ClO2 gas deodorizing delivery system that works in 4 to 6 hours in an empty room and is Not for use with/on plants/crops/feed.
Continuous air treatment with plants present
For ongoing air quality while plants are in place, ProKure D is the slow-release gas that provides ClO2 protection for up to 30 days and improves air quality and controls odors. ProKure D is not an EPA-registered product and is not labeled for sale as a pesticide under 40 CFR, and it carries no surface-kill claim. It runs with the crop; it does not disinfect the tray.
Direct plant contact
No ClO2 product in this line goes on the plant itself. Not V, not G, not D. Surfaces and air, never foliage.
Related resources


