ProKure G 10g Pouch: Fast-Release ClO2 Gas for Between-Cycle Room Turnover (Up to 1,000 ft3)

The ProKure G 10g pouch is the smallest single-unit SKU of ProKure G fast-release chlorine dioxide gas, and it is sized for a small grow room. One 10g pouch treats up to about 1,000 cubic feet of sealed, unoccupied space for standard odors, or about 500 cubic feet for a heavy load. You activate it with water in a reusable dispersion cup, leave the empty room for at least 4 to 6 hours, and ventilate and turn on the lights for one hour before re-entry. It leaves no residue to rinse. ProKure G is EPA-registered as Reg. No. 87508-2-89334 and not for use with plants, crops, or feed, so it runs only when the room is empty.

If your room is bigger than 1,000 cubic feet, the 25g pouch is the better fit, and if you are reordering at scale, the case is the right SKU. This page answers one question: should you buy the single 10g pouch for your room. For the full product line and mechanism, see the ProKure G fast-release gas overview.

What the 10g pouch is

The 10g pouch is a water-activated chlorine dioxide gas generator in a sealed foil packet. The manufacturer describes ProKure G as the solution to mold and mildew, odor-causing bacteria, and chemical odors, delivered as a deep-penetrating vapor. The 10g is the single-pouch, smallest-coverage unit of that line.

The spec at a glance: a 10-gram (0.35 ounce) pouch, rated for up to about 1,000 cubic feet of standard-odor treatment or about 500 cubic feet for heavy odors, paired with a reusable gas dispersion cup, activated with roughly an inch and a half of water, and EPA-registered as Reg. No. 87508-2-89334.

Fast-release is the other half of the name, and it matters for choosing it over its sibling. ProKure G works through its charge in hours, which is what you want for a turnover: activate, hold 4 to 6 hours, ventilate, done. That is the opposite of ProKure D, the extended-release gas that trickles a trace level over up to 30 days for ongoing air quality with plants present. If you want a fast empty-room reset, that is G; if you want a slow in-cycle hold, that is D.

Coverage math: is the 10g right for your room?

Measure your room as length times width times ceiling height, in feet, to get cubic feet, then compare to the pouch rating. The 10g covers up to about 1,000 cubic feet for standard odors.

A few common geometries. A 4 by 4 tent at an 8-foot ceiling is 128 cubic feet, well inside one 10g. A 4 by 8 tent at 8 feet is 256 cubic feet, still one 10g. A 10 by 10 room at a 10-foot ceiling is 1,000 cubic feet, which is exactly one 10g at the standard rating, or one 25g if the room came off a heavy mold cycle. An 8 by 8 room at 8 feet is 512 cubic feet, one 10g.

Two rules keep you from under-dosing. First, the 1,000-cubic-foot figure is for standard odors; for a heavy load the same pouch effectively covers about 500 cubic feet, so step up a size or add a pouch when a room fought mold all cycle. Second, count the full room volume, including the space above the canopy, and do not subtract benches or equipment. When a room runs over 1,000 cubic feet, move to the 25g, which covers about 2,250 cubic feet, rather than stacking 10g pouches. For room-by-room sizing across a facility, the grow-room air quality and coverage guide works the math.

How to use a ProKure G 10g pouch between cycles

The 10g earns its place in the 3-to-5-day turnover window. Run it as a sequence.

Clear the room: plants, people, and pets out, since the label restriction is absolute. Seal it: cover smoke detectors, and set shared ventilation to recirculate or close the ducts so you are not pushing gas into occupied space. Activate: tear the foil, remove the white inner pouch without opening it, place the indented end in the dispersion cup with about an inch and a half of water, set it high and central with a fan running, and turn off the lights. Then leave.

Hold and return: give the system at least 4 to 6 hours, or run it overnight, then ventilate and turn on the lights for one hour before re-entry. Mark the treatment and safe re-entry times on the caution placard the product ships with. Then the next crop goes in. Because the gas leaves no residue, there is no rinse-and-dry step eating the back end of your turnover. For the step-by-step activation detail, the product overview carries it; this page is about whether the 10g is the right unit.

EPA registration and label restrictions

This is the part a procurement or QA reader needs on the page, not buried. ProKure G is EPA-registered, Reg. No. 87508-2-89334, and it is a violation of federal law to use an EPA-registered product in a manner inconsistent with its labeling. For the 10g pouch that means the empty-room rule and the ventilation step are registered conditions of use, not suggestions.

The label restriction to write into any SOP: not for use with plants, crops, or feed. ProKure G runs only in an unoccupied room with no people, pets, or plants present during treatment. That is the single most common place a first-time buyer goes wrong, assuming a small pouch is mild enough to run near a canopy. It is not; the restriction is the same at 10g as at any size. Keep the current product label and SDS on file from prokuresolutions.com, and note that while EPA registration is federal, state pesticide registration varies, so confirm your state status before you standardize.

ProKure G versus bleach, quats, and foggers

The 10g pouch competes with whatever you were resetting the room with before, and the comparison is where its value shows.

Against bleach and quats, the difference is residue and re-entry. A wet bleach or quat protocol leaves a residue or film that must be rinsed and dried before the next crop, and the fumes can force crew out of the space. The ProKure G gas treats the whole sealed volume and dissipates with no film to rinse, so the back-end rinse-and-dry stage that stretches a wet turnover past a single shift simply is not there. Against ozone foggers, the difference is material compatibility and registration: ozone is harsh on rubber and equipment over time and is not an EPA-registered pesticide for this use, while ProKure G is registered and, with the label's 18-to-24-inch clearance from sensitive surfaces, runs with equipment in place. The honest limit: G treats the air and surfaces of an empty room, it does not replace a carbon filter during a live cycle, and it is not a surface-wipe disinfectant, which is the liquid ProKure V's job.

When to use ProKure G versus ProKure D and ProKure V

The 10g pouch is one product in a three-part system, and matching it to the moment is the whole decision.

ProKure G, including this 10g pouch, is the fast empty-room reset: sealed, unoccupied, between crops, EPA-registered. ProKure D is the extended-release gas that runs with plants present for up to 30 days of ongoing air quality, is not EPA-registered, and carries no kill claims, so it is the in-cycle maintenance layer, not a turnover tool. ProKure V is the liquid surface disinfectant, EPA-registered as Reg. No. 87508-3-89334 and suitable for use with plants in the room on hard, non-porous surfaces, so it is the wipe-and-dip product. If the room is empty and you want the air reset fast, the 10g pouch is right. If plants are in, that is a ProKure D slow-release job or a ProKure V surface job, not a 10g pouch.

How to buy the 10g pouch, and FAQs

Buy the single 10g pouch when you are running one small room or sampling the product before you commit to case quantities, and reorder through shop.groclarity.com. When you are running a scheduled turnover protocol and pulling more than a few pouches per cycle, the case is the reorder SKU and the better per-unit value. For the full label, SDS, and spec sheet, go to prokuresolutions.com.

The questions below mirror the label and the common sizing questions a small-room operator asks. Confirm the specifics against the current product label before you treat a room, and for a multi-room or multi-state program with account pricing, reach a GroClarity specialist at 866.206.1301.

Related resources