Does ProKure V Kill MRSA on Surfaces? EPA-Registered Kill Claim, Contact Time, and Use Conditions

Yes. ProKure V is an EPA-registered Hospital-Type Disinfectant (EPA Reg. No. 87508-3-89334), and methicillin-resistant S. aureus (MRSA, ATCC 33591) is on its label kill list for hard, non-porous surfaces. The label condition is specific: an exposure time of 10 minutes at 100 ppm. It is suitable for use with plants in the room and leaves no residue, which is the combination a cultivator cannot get from bleach or a quat. One rule governs all of this. It is a violation of Federal Law to use this product in a manner inconsistent with the labeling, so read the entire label and use it strictly in accordance with the directions.

Why you probably landed on a marketing number instead of a label

You likely got here after reading kills MRSA somewhere that gave you a percentage and no proof. An Amazon listing promises Eliminate 99.9999% MRSA with zero test parameters. A Facebook post lumps MRSA into a 99.999 percent of bacteria and viruses claim next to H1N1, HIV, and Legionella. Those numbers are not where you verify a kill claim. You verify it against the EPA-registered label, by registration number, strain, and contact time, which is exactly what none of those posts give you.

Here is the honest version of what ProKure V is. It is a liquid Hospital-Type Disinfectant you activate by adding water, then apply directly. The #1 ranking retail page for this exact query says ProKure V can be applied by spraying, pouring, and mopping, and its neutral pH makes it compatible with almost any surface, and that it is used to eliminate bacteria, viruses, mold and mildew on hard surfaces. True as far as it goes. What that page never does is name MRSA, name the strain, or state the contact time. The claim you came to verify is not on the page that ranks first for it.

That gap is the whole reason this page exists. A proof-anchor page should lead with the registration number, name the organism and strain the label actually tested, state the contact time, and then tell you plainly what the product does not do. The sections below do that in order.

What MRSA is and why a hard-surface kill claim matters

MRSA is a strain of Staphylococcus aureus that resists several common antibiotics. It spreads person to person and, importantly for a facility, by way of contaminated surfaces. A door handle, a trim table, a tote, a shared tool: any hard surface a contaminated hand touches can become a transfer point. That is why surface disinfection, not just hand hygiene, is part of the control story.

In a cannabis cultivation facility, the stakes are specific. A head grower responsible for a six-figure harvest is already running between-cycle sanitation to keep yeast and mold load under the state pass threshold. MRSA control folds into the same workflow: the same hard, non-porous surfaces (stainless trim tables, sealed concrete, glass, plastic trays, trellis frames) get the same disinfectant pass. A residue-free disinfectant that is suitable for use with plants in the room means you are not forced to tear the room down and evacuate the crew to run it, the way a bleach protocol often forces.

In a food-contact setting (a commissary, a bakery, a cannabis edibles kitchen), the surface hygiene story carries an added credential, the NSF D2 sanitizer category, which the section on residue covers below. In a general commercial facility (a gym, a clinic waiting room, a locker room), the same hard-surface kill claim applies to the same material list. One product, three reader contexts, one label.

The ProKure V MRSA kill claim, verbatim from EPA Reg. No. 87508-3-89334

Here is the claim as the registered label frames it, with nothing added. ProKure V must be used with an exposure time of 10 minutes at 100 ppm to disinfect a bacterial kill list that includes methicillin-resistant S. aureus (MRSA) (ATCC 33591), alongside Staphylococcus aureus (ATCC 6538), Pseudomonas aeruginosa (ATCC 15442), and others. MRSA is named by strain, ATCC 33591, and tied to that 10-minute dwell at 100 ppm on hard, non-porous surfaces. That is the verifiable claim. A procurement or QA lead can take that registration number, strain, and contact time to a state auditor without a marketing asterisk hanging off it.

Two honesty notes belong right here. First, a round percentage is not what the label publishes for MRSA, so this page does not quote one. The label publishes the organism, the strain, and the use condition, and that is the defensible claim. If you have seen a 99.9999 percent MRSA figure on a marketplace listing, treat it as marketing language from a reseller, not as the label claim. Second, the contact time is not instant. The 10-minute dwell is the condition of the claim. The surface has to stay visibly wet for those 10 minutes. A quick wipe-and-walk does not meet the label.

The surfaces the claim covers are the hard, non-porous ones the label enumerates: stainless steel, glass, vinyl, polypropylene, PVC, and other hard, non-permeable surfaces. In facility terms, that is your trim tables, grow beds, drying and cure room surfaces, trellis frames, totes, and sealed, non-porous bench tops. Visibly soiled surfaces get pre-cleaned first with a non-disinfectant cleaner, because organic soil shields organisms from any disinfectant.

How to apply ProKure V so the MRSA claim actually holds

The claim is only true if the application matches the label, so three things have to line up: concentration, method, and dwell. The concentration is 100 ppm, which you reach by activating the correct pouch size in the correct volume of water in an opaque (not clear) container and letting it reach full strength. The method is direct application by sprayer, mop, or sponge. You do not fog it. The manufacturer FAQ is explicit: No. ProKure V should be applied by sprayer, mop, or sponge to disinfect all hard, non-porous surfaces. The dwell is the 10 minutes of visible wetness the MRSA line requires.

PPE is lighter than most people expect at this concentration, and the FAQ states it plainly: respiratory PPE is not required when using ProKure V at 100 PPM. The one exception is hands. If your hands will contact the activated solution during dilution or application, wear protective gloves. That is the whole PPE picture at 100 ppm, which is part of why crews can run it without the evacuation a bleach fog demands.

For the step-by-step mixing and application walkthrough (pouch size to water volume, agitation schedule, and the hold-to-full-strength timing), that is a sibling topic and not re-taught here. This page stays on the MRSA claim: what it is, what condition makes it true, and what it does not cover.

Using ProKure V with plants in the room, and what the label does not allow

The wedge claim for ProKure V is a short sentence doing a lot of work: it is a hospital-type disinfectant suitable for use with plants in the room. The manufacturer FAQ confirms it: Yes, ProKure V is suitable for use with plants in the room. That is the combination bleach and quats cannot offer, because their residue is exactly what you do not want near a living, saleable crop.

Now the limit, stated as plainly as the claim. Suitable for use with plants in the room is a statement about the surface disinfection happening in the same space as the plants. It is not a license to apply the product onto the plants, the crop, or the growing media as a treatment. ProKure V is a hard, non-porous surface disinfectant. The MRSA claim lives on surfaces. Keep the application on the trim table, the tote, the bench, and the tool, not on the canopy.

If the air side of the room is the actual problem (odor, between-cycle reset, mold load in an empty room), that is a different product and a different label. ProKure G is the fast-release gas for the empty-room reset, and it carries its own verbatim restriction, Not for use with/on plants/crops/feed, so it runs only when the room is cleared. Do not borrow G's restriction and pin it on V, and do not expect V's surface claim to do G's air-side job. Each product carries its own label.

Residue, food contact, and the NSF D2 category

Residue is where ProKure V separates from the alternatives, and the FAQ answer is one word. Does ProKure V leave a residue behind? No. For a food-contact operator that matters beyond cleanliness, because it changes whether a rinse step is required. ProKure V holds an NSF International certificate in the D2 category, which means it is considered a sanitizer on surfaces that do not always require a rinse. A commissary or edibles kitchen can fold the same disinfectant that carries the MRSA surface claim into a food-contact sanitation step without a mandatory rinse everywhere, subject to the label.

That residue-free, no-rinse profile is also why the surface claim is practical in a working grow. You are not introducing a new residue onto surfaces that sit near a crop, and you are not adding a rinse-and-dry cycle to an already tight between-cycle turnover window.

ProKure V versus bleach, quats, and isopropyl alcohol for MRSA

Facility managers usually search this exact claim because they are deciding whether to switch off bleach or a quat, and the People Also Ask box on this query is full of the same comparison instinct: Will Lysol wipes kill MRSA? Can isopropyl alcohol kill MRSA? The honest frame is category-level, not a head-to-head against any single branded product.

Bleach (sodium hypochlorite) can carry a hard-surface disinfection claim, but it leaves residue, it is corrosive to many surfaces over time, and its fumes are what force a crew to evacuate a grow room. Quaternary ammonium (quat) cleaners also leave residue on plant-contact surfaces, which is the exposure a cultivator is trying to avoid near a crop. Isopropyl alcohol flashes off fast, which cuts the dwell time a surface kill claim depends on, and high-concentration alcohol is a flammability and cost problem at facility scale.

Against that category backdrop, ProKure V's position is specific and label-backed: an EPA-registered Hospital-Type Disinfectant with MRSA (ATCC 33591) on the kill list at 10 minutes and 100 ppm, that leaves no residue and is suitable for use with plants in the room. The comparison is not which one kills, it is which one kills and leaves you a surface you can keep a crop next to.

What ProKure V does NOT do, and how to buy it

An honest proof page names the limits. ProKure V does not provide lasting protection after it dries. The manufacturer FAQ is clear that ProKure V cannot prevent future events of infection or contamination and should be re-applied if there has been a chance for re-contamination or per your ongoing facility protocols. It is a point-in-time surface disinfectant, not a residual coating. It is also a surface product, not an air treatment, and not a plant treatment. And the MRSA claim holds only at the labeled 100 ppm and 10-minute dwell, not at a faster wipe.

For a facility building a MRSA response into its SOPs, the workflow is: pre-clean visible soil, apply ProKure V at 100 ppm to the hard, non-porous surfaces, hold 10 minutes of visible wetness, and log the date, surfaces treated, concentration, and operator initials so a state or internal QA auditor can follow the trail. Keep the EPA label and SDS for EPA Reg. No. 87508-3-89334 on file from prokuresolutions.com for that audit.

When you are ready to order, the pouch sizes and reorder path live on shop.groclarity.com, where a 0.17 oz pouch makes one gallon of activated solution. If you run multiple facilities and want a standardized surface-plus-air protocol, a GroClarity contact can scope it across sites. Always read product labels before use.

Related resources