Yes, under labeled conditions. ProKure V is EPA-registered (87508-3-89334) and its label names Aspergillus niger (ATCC 9642) as an organism it controls as a fungicide on hard, non-porous surfaces, at 100 ppm for a 10-minute exposure. That is the exact claim: a specific strain, a specific concentration, a specific contact time, on surfaces, not on the plant. It is a hard-surface disinfectant suitable for use with plants in the room, which is what lets it reduce the Aspergillus load in a grow between and during cycles. It is a violation of federal law to use it inconsistent with the label.

Does ProKure V Kill Aspergillus? The EPA-Registered Label Claim, Explained for Cultivators

You are not here for a product overview. You are here for a yes-or-no efficacy answer tied to a specific organism, probably because a harvest just failed a test, because QA is building an audit binder, or because a head grower wants confirmation before the purchase order goes in. So here is the answer with the conditions attached, because the conditions are the claim.

ProKure V is an EPA-registered chlorine dioxide (ClO2) liquid, registration number 87508-3-89334. On hard, non-porous surfaces, used at 100 ppm for a 10-minute exposure, it is an effective fungicide against Aspergillus niger (ATCC 9642). That strain ID and those parameters are not decoration; they are the boundary of the registered claim, and a QA binder that cites them is citing the label correctly. This page explains what that claim covers, what it does not, and how it maps to what your state actually tests for.

The short answer, with the label conditions

ProKure V's registered fungicidal claim against Aspergillus niger is parameter-bound: 100 ppm ClO2, 10-minute exposure, hard non-porous surfaces. Change any of those and you are outside the claim. Used that way, it is a legitimate, label-conformant Aspergillus control step for surfaces in a cultivation facility, and because V is suitable for use with plants in the room, you can run it as a surface step without pulling the crop. It is not a plant-tissue treatment and it is not applied to the canopy. Always follow the EPA-registered label.

What Aspergillus is, and why cannabis regulators test for it

Aspergillus is a genus of spore-forming mold, and it is the compliance-critical one in cannabis because several species are flagged in state testing. The spores are airborne and settle on surfaces, which is why a sanitation program that keeps surfaces and environmental load down is a prevention step, not just a cleanup.

The species state panels test for

Most state panels test for four Aspergillus species: Aspergillus flavus, Aspergillus fumigatus, Aspergillus niger, and Aspergillus terreus, usually as a speciation screen that triggers a hard fail if any is detected. This is the distinction that matters for an honest efficacy answer. ProKure V's EPA-registered fungicidal claim names Aspergillus niger (ATCC 9642) specifically; it does not carry registered kill claims against flavus, fumigatus, or terreus. So the accurate statement is that V is registered against A. niger on hard surfaces and that, as a broad-spectrum ClO2 surface disinfectant, it reduces the environmental Aspergillus load that drives failures, but you should not claim or document it as a registered kill for the species it is not registered against.

TYM versus Aspergillus speciation

States run two related tests: total yeast and mold (TYM), reported as colony-forming units per gram, and an Aspergillus speciation screen. TYM is a load measure; the speciation screen is a presence-or-absence pathogen test. The thresholds vary by state, so defer to your own state's current rule. A surface sanitation program with V reduces the load that shows up in TYM and the surface spore reservoir that feeds a speciation positive.

Why a positive costs a harvest

An Aspergillus speciation positive is typically a hard fail, which means the affected lot cannot go to market. On a mature crop that is a six-figure loss, which is why the search behind this query is often a post-fail triage, and why the prevention argument, keeping the surface and environmental load down across every cycle, is the one that actually protects revenue.

The mycotoxin link raises the stakes further. Aspergillus species produce mycotoxins such as aflatoxins and ochratoxin A, which several states cap on a separate panel, so an Aspergillus problem is often two compliance problems at once: the pathogen screen and the mycotoxin cap. Preventing the mold prevents the toxin, which is the cleanest argument for treating surface sanitation as a scheduled control rather than a reaction to a failed result. A standing V surface program is upstream of both tests.

The ProKure V label claim on Aspergillus, unpacked

The claim is only as good as the conditions, so here is each one.

ATCC 9642 is the test strain

The label claim rests on Aspergillus niger (ATCC 9642), a defined reference strain. Naming the strain is what makes the claim auditable: a QA record that says "effective fungicide against Aspergillus niger ATCC 9642 per EPA Reg. No. 87508-3-89334" is citing the registered claim precisely, which is exactly what a compliance binder needs.

100 ppm is the required concentration

The fungicidal claim is at 100 ppm ClO2. You activate a ProKure V pouch in water to reach that concentration, and the dilution tables on the label give the pouch-to-water ratios: a 3.36 oz pouch to 20 gallons, 0.84 oz to 5 gallons, 0.17 oz to 1 gallon, and 0.042 oz to 1 quart, all to achieve 100 ppm. Under-dilute or over-dilute and you are off the claim.

10 minutes is the contact time

The exposure time is 10 minutes at 100 ppm. The surface has to stay visibly wet for the full contact time; a quick wipe that flashes off does not meet the claim. Plan the application so the treated surface holds wetness for the duration, re-wetting a vertical or fast-drying surface if needed to hold contact for the full ten minutes. Contact time is the variable operators shortchange most, usually by treating a spray-and-move pass as a disinfection step when the registered claim requires the surface to stay wet the whole ten minutes.

Hard, non-porous surfaces only

The claim is for hard, non-porous surfaces: stainless steel, glass, vinyl, PVC, polypropylene, and similar materials. Pre-clean visibly soiled surfaces first, because organic soil blocks contact. The claim does not extend to porous surfaces, to the air, or to plant tissue.

What the label does not claim

V's Aspergillus claim is not a fogging claim, not an air-treatment claim, and not a plant-tissue claim. If you need air treatment, that is a gas product, not V. If you need a kill claim against A. flavus, fumigatus, or terreus specifically, the label does not provide it. Staying inside the claim is what keeps the use compliant.

This matters for how you write a QA record. The temptation under a failed speciation test is to document "ProKure V kills Aspergillus" as a blanket statement, but the defensible record names the registered organism and conditions: A. niger (ATCC 9642) at 100 ppm for 10 minutes on hard non-porous surfaces. An auditor reading the precise claim sees a program that understands its own compliance boundary; an auditor reading an overclaim sees a facility that does not. Precision is the safer position, and it happens to be the truthful one.

Why ClO2 works on Aspergillus when bleach and quats struggle

ProKure V is chlorine dioxide, an oxidizer, and the chemistry is why it fits a grow room where conventional sanitizers do not.

ClO2 works by oxidation at low concentration rather than by chlorinating organics the way bleach does, so it attacks the spore's structure directly and does not leave the chlorinated byproducts or the residue bleach and quaternary ammonium cleaners leave behind. That residue is the reason bleach and quats are a problem near a crop, and it is why V's "leaves no residue" property matters: you can disinfect a bench next to a plant without a rinse step.

The other advantage is that V is suitable for use with plants in the room, the exact label language, because it treats the surface and not the crop. That single combination, a registered hard-surface fungicide against A. niger that you can use with plants present and that leaves no residue, is what bleach and quats cannot offer, and it is why V is the surface half of a cannabis IPM program. For the upstream chemistry in full, see the mold prevention protocols overview.

There is also a resistance argument. Because ClO2 destroys the spore's structure by oxidation rather than interfering with a single metabolic pathway, there is no sub-lethal mechanism for a mold population to adapt around, the way it can with a rotation of mode-of-action fungicides. A surface program built on V does not lose efficacy over cycles the way a chemical-fungicide rotation can, which is part of why it reads as a durable control for a QA team planning years of harvests rather than one crop.

The Aspergillus remediation and prevention protocol

Here is how the claim becomes a program, from a post-fail triage to a standing cadence.

Post-fail triage

After a positive TYM or Aspergillus result, isolate the affected lot or room so the problem does not spread through shared air, and document the result immediately. Surface-disinfect the hard, non-porous surfaces with V at 100 ppm for a 10-minute wet-contact exposure. For the air in an emptied room, hand off to the fast-release gas; V is the surface step, not the air step. Pre-clean visibly soiled surfaces first with a non-disinfectant cleaner, because organic soil shields spores from contact and a visibly dirty surface will not meet the claim no matter how long you leave the solution on it. Re-test before anything goes back in, and keep the positive result, the remediation steps, and the clean re-test together as a single documented event for the state.

Preparing V to the 100 ppm claim

Activation is a defined procedure: open the foil packet, drop the white inner pouch (do not open it) into an opaque, non-clear container with the label-specified amount of water, and agitate for one minute at 15-minute intervals until full activation at one hour, five agitations total. Allow the full hour before use so the solution reaches full strength, and keep the temperature in the labeled range. Activated solution has a working life: use stored formula within 15 days of activation and record the activation date on the container.

Routine cadence and documentation

Between harvests, run V as the surface-disinfection step of every room turnover so the Aspergillus reservoir never builds across cycles. Log each treatment: the product, the 100 ppm concentration, the 10-minute contact time, the room or surface, the activation timestamp, and the operator, and keep the EPA label and SDS on file. That log is what turns a protocol into audit evidence. For the activation walkthrough, see the step-by-step activation guide, and for the label and SDS, the compliance doc hub has the downloads.

The application sites that matter most for Aspergillus are the ones that touch flower after harvest: trim tables, drying-room racks, curing bins, trays, and the tools that move between them. The label names cultivation rooms, grow beds, drying rooms, cure rooms, vegetation rooms, propagation rooms, trimming areas, and mother rooms as application sites, which covers the full path a spore travels through a facility. Build the cadence around that path rather than treating sanitation as a single room event, because Aspergillus does not respect room boundaries and neither should the program.

One activation note worth repeating because it is where operators lose the claim: the solution must reach full strength before use. You activate, wait the full hour with the label's agitation schedule, and only then apply at 100 ppm for the 10-minute contact. Skipping the hour means applying an under-strength solution that does not meet the registered concentration, which quietly voids the claim even though the bottle looks the same.

What ProKure V is not, and when to reach for ProKure G

Knowing the boundary is as important as knowing the claim.

The compliance boundaries

ProKure V is not a plant-tissue fungicide, not a fumigant or air treatment, and not for potable water. Its Aspergillus claim is a hard-surface claim against A. niger under the labeled 100 ppm, 10-minute conditions. Using it outside those conditions, or documenting it as something it is not, is where compliance problems start. It is a violation of federal law to use an EPA-registered product in a manner inconsistent with its labeling.

V for surfaces, G for air

The decision is clean once you know where the positive came from. A surface swab positive calls for V on the surfaces. An air sample positive calls for the fast-release gas, ProKure G, in an empty room, since G is EPA-registered (87508-2-89334) for the air but is labeled "Not for use with/on plants/crops/feed," so it runs empty-room only. If both are positive, you run V on surfaces and then a G reset in the emptied room. For the full selection logic, see the ProKure V versus G comparison.

The reason the two are not interchangeable comes back to form. V is a liquid that reaches only what you wet, which makes it precise on surfaces and useless on the air in the corners of a room. G is a gas that fills the volume and reaches ducting and shaded undersides a sprayer misses, but it cannot run with a crop present. So the honest framing is that an Aspergillus program uses both, matched to where the organism actually is, rather than asking one product to cover a job the other is built for.

Documentation for auditors

An auditor cannot see your intentions, only your records, so the documentation is the deliverable.

Keep the EPA-registered label and the SDS for ProKure V on file, downloadable from the compliance doc hub, and pair them with a treatment log that records the 100 ppm concentration, the 10-minute contact time, the activation timestamp, the surface or room, and the operator. A QA binder that cites "Aspergillus niger ATCC 9642, EPA Reg. No. 87508-3-89334, 100 ppm, 10-minute exposure" is citing the registered claim exactly, which is the strongest position at audit.

For a multi-state operator, the documentation burden multiplies, so standardize it: one log template, one set of label and SDS files, and one activation procedure used at every facility, with a per-state layer that notes each market's specific TYM threshold and speciation requirement. Thresholds vary by state and change over time, so the per-state layer is where you track the current rule rather than hard-coding a number into the SOP itself. That structure keeps the core program identical across the footprint while staying accurate to each jurisdiction, which is exactly what a cultivation director defending the standard to a regulator needs. GroClarity's air-testing service adds before-and-after sampling you can show an inspector, and for account pricing or a multi-facility standard, request a quote; to order, the ClO2 line is on shop.groclarity.com, and spec sheets and SDS live on prokuresolutions.com.

Frequently asked questions

Does ProKure V kill Aspergillus?

Yes, under labeled conditions. ProKure V is EPA-registered (87508-3-89334) as an effective fungicide against Aspergillus niger (ATCC 9642) on hard, non-porous surfaces, at 100 ppm for a 10-minute exposure. The claim is parameter-bound to that strain, concentration, contact time, and surface type, and it is a surface treatment, not a plant or air treatment.

Does ProKure V kill A. flavus, fumigatus, or terreus, or only A. niger?

V's EPA-registered fungicidal claim names Aspergillus niger (ATCC 9642) specifically. It does not carry a registered kill claim against A. flavus, A. fumigatus, or A. terreus, the other species on most state panels. As a broad-spectrum ClO2 surface disinfectant it reduces the environmental Aspergillus load, but you should document only the registered claim (A. niger) and not represent it as a registered kill for the species it is not registered against.

Can I use ProKure V with plants in the room during Aspergillus remediation?

Yes. ProKure V's label states it is suitable for use with plants in the room, because it is a hard-surface disinfectant that treats the surface rather than the crop and leaves no residue. You apply it to benches, trays, tools, and other hard surfaces, not to the plant, and you keep the application off the canopy. Follow the EPA-registered label directions.

How does ProKure V compare to ProKure G for Aspergillus?

ProKure V handles surfaces; ProKure G handles air in an empty room. A surface-swab positive calls for V at 100 ppm for 10 minutes. An air-sample positive calls for G, which is EPA-registered (87508-2-89334) but labeled not for use with plants, crops, or feed, so it runs empty-room only. If both are positive, do V on surfaces and a G reset in the emptied room.

What is the EPA registration number for ProKure V?

ProKure V's EPA registration number is 87508-3-89334. Cite it alongside the strain (Aspergillus niger ATCC 9642) and the labeled conditions (100 ppm, 10-minute exposure, hard non-porous surfaces) in any compliance record, and keep the full EPA-registered label and SDS on file for audit.

How much does ProKure V cost?

Pricing varies by SKU and by order volume, and a facility buying by the case pays a different number than a single packet. We do not publish a fixed price here; request a quote from GroClarity for account-level pricing, order the line on shop.groclarity.com, and find spec sheets and SDS on prokuresolutions.com. Built on Science. Backed by Results.

Related resources