ProKure V for Grow Bench Disinfection
ProKure V disinfects grow benches as a liquid chlorine dioxide applied to hard, non-porous surfaces, and its label (EPA Reg. No. 87508-3-89334) states it is suitable for use with plants in the room. For a bench, you pre-clean the surface, apply ProKure V at 100 ppm by sprayer, mop, or sponge, hold a 10-minute contact time, and let it air dry. It leaves no residue and requires no rinse, so a disinfected bench is ready for the next tray without a rinse-and-dry step. Benches are a top reinfection surface, which is why a bench-specific protocol matters.
Why grow benches are a primary reinfection surface
A bench top is where the last crop sat and where the next one will sit. Spores and bacteria that drip, shed, or splash off plants collect on the tray and the frame, and an ebb-and-flow bench adds standing water that feeds biofilm. Botrytis, powdery mildew, and root-zone pathogens all persist on these surfaces between cycles.
The bench and the irrigation emitters that run across it overlap, so a bench that looks clean can still reseed the next crop from residue in the tray channels and around the drippers. Disinfecting the bench surface is one of the highest-leverage steps in a between-cycle reset because it breaks that carryover.
What ProKure V is, and why bench surfaces fit its label
ProKure V is a water-activated liquid that generates chlorine dioxide. You tear the foil packet, drop the inner pouch into an opaque container of water, agitate at 15-minute intervals, and allow one hour for the solution to reach full strength at 100 ppm. Do not open the white inner pouch. The label directs an exposure time of 10 minutes at 100 ppm to disinfect hard, non-porous surfaces.
Its registration is the reason a bench is a textbook use site. EPA Reg. No. 87508-3-89334 covers hard, non-porous surfaces in cultivation rooms and the directions state the product is suitable for use with plants in the room. ProKure V leaves no residue and requires no rinse on treated surfaces. Grow-bench tops and frames are exactly the hard, non-porous surfaces the label describes.
Two boundaries to keep straight. ProKure V is for hard, non-porous surfaces, not for spraying directly onto plants and not for porous materials that will not hold a disinfectant contact. It is a surface disinfectant; it treats the bench, not the crop.
Bench material compatibility
Most bench materials a cultivator runs are hard and non-porous, which is what ProKure V is registered for. Aluminum rolling-bench frames, ABS and HDPE ebb-and-flow trays, powder-coated steel racking, and wire or mesh benches are all hard, non-porous surfaces, and the product is described as compatible with almost any surface when applied to visible wetness.
The materials to watch are the porous ones. A raw plywood or MDF bench top is not a hard, non-porous surface; it absorbs liquid rather than holding a surface contact, so it is not a label-appropriate target. Where a bench has a painted or sealed top, test an inconspicuous spot first for finish compatibility before you treat the whole surface.
The bench reset protocol between crops
Run the bench reset as a short, repeatable sequence. First, strip the bench of plants, media, and trellising so the surface is clear. Second, remove dry debris, a HEPA vacuum rather than a broom so you do not aerosolize spores. Third, pre-clean organic residue and mineral scale, because a disinfectant works on a clean surface, not through a layer of grime; the label directs pre-cleaning visibly soiled surfaces.
Fourth, mix ProKure V to 100 ppm for the volume you need. Fifth, apply to visible wetness by sprayer, mop, or sponge and hold the 10-minute contact time at 100 ppm. Sixth, air dry or wipe; no rinse is required on hard, non-porous bench surfaces. Seventh, document the reset: product, EPA registration number, concentration, dwell time, operator, and date. That log is what turns the step into audit evidence.
In-cycle bench work with plants adjacent
The plants-in-room approval is what sets ProKure V apart for bench work. Because the label states the product is suitable for use with plants in the room on hard surfaces, you can disinfect a bench top while live plants sit on the bench next to it, provided you apply to the surface and not to the crop. That is the exact job a cultivator with a positive mold test needs: spot-treat the affected bench without evacuating the room.
On PPE, the manufacturer FAQ states that at 100 ppm through a pressurized sprayer ProKure V does not require respiratory PPE, with gloves needed where hands contact the activated solution during dilution or application. Always read the product label before use.
Sizing ProKure V by packet
ProKure V is sold by yield at 100 ppm. The 0.042 oz packet makes one quart (32 oz) for a small bench spot treatment. The 0.17 oz packet makes one gallon, enough for a single rolling bench. The 0.84 oz packet makes five gallons for a room of benches, and the 3.36 oz packet makes 20 gallons for a full facility turnover. Pick the packet that matches the surface area you are treating so you mix what you will use within the activated solution's stated storage window.
Frequently asked questions
The questions below cover what cultivators ask most about bench disinfection with ProKure V. For the full product explainer, see the ProKure V liquid disinfectant page; for the between-cycle room reset, see the air-quality management line.
Related resources


