ProKure V 3.36oz Liquid Disinfectant, 20-Gallon Yield at 100 ppm ClO2

One ProKure V 3.36oz packet (SKU 185-V336C) activates into 20 gallons of disinfectant solution at 100 ppm chlorine dioxide. You prepare it in an opaque 20-gallon drum, agitate for one minute at 15-minute intervals until full activation at one hour, and you have 20 gallons of hospital-type disinfectant that leaves no residue and is suitable for use with plants in the room. At $56.95 for a single packet, that works out to $2.85 per activated gallon, the lowest of any ProKure V size. The 12-pack case (185-V336C12) holds the same ratio across 240 gallons, and the packet carries EPA Reg. #87508-3-89334.

The 3.36oz packet at a glance

The 3.36oz packet is the largest size in the ProKure V ladder, and it exists for one reason: volume. A single packet weighs 95.2 grams and yields 20 gallons of solution at a nominal concentration of 100 ppm. The SKU is 185-V336C for a single packet and 185-V336C12 for the 12-pack case. The regulatory anchor is EPA Reg. #87508-3-89334 and EPA Est. #62788-AL-001, which the ProKure Solutions industrial pricing table lists verbatim.

What you get at label strength is a disinfectant, tuberculocide, fungicide, general-purpose antimicrobial, and surface cleaner for hard, non-porous surfaces. The approved ProKure descriptors are plain: hospital-type disinfectant, kills mold and mildew, suitable for use with plants in the room, leaves no residue. That last line is the part that matters in a grow room. Bleach and quats cannot say it.

What the packet is not: an air treatment. ProKure V is the liquid half of the system. It disinfects surfaces at 100 ppm with a 10-minute exposure time. If your problem is airborne odor or air quality between cycles, that is a ProKure G or ProKure D job, and we will get to the handoff later on this page.

Why the 3.36oz SKU is the cost-per-gallon leader

Here is the math no reseller page does for you. Run the division across all four ProKure V sizes using the factory-direct single-packet prices from the ProKure Solutions industrial table:

  • 3.36oz packet, $56.95, makes 20 gallons: $2.85 per activated gallon.
  • 0.84oz packet, $31.95, makes 5 gallons: $6.39 per activated gallon.
  • 0.17oz packet, $21.95, makes 1 gallon: $21.95 per activated gallon.
  • 0.042oz packet, $19.95, makes 32 oz (a quarter gallon): $79.80 per activated gallon.

The 3.36oz packet is roughly half the per-gallon cost of the 0.84oz, and a fraction of the small sizes. The 12-pack case (185-V336C12) holds the same ratio: $683.40 for 240 activated gallons is still $2.85 per gallon. If you disinfect at any real volume, the 3.36oz is the SKU that pays for itself.

That does not make it the right packet for everyone. If you spot-treat a single bench or wipe down one room's drop-down hoses, 20 gallons of activated solution has a 15-day clock on it (more on that below) and you will pour most of it out. A single-room operator is usually better served by the 0.84oz 5-gallon size. The 3.36oz earns its place when you are turning over multiple rooms back to back and a 5-gallon batch forces too many mix cycles.

How to activate a 3.36oz packet, step by step

The activation protocol is label copy, restated for the 20-gallon drum. Do not improvise it.

Step 1. Tear open the foil package and remove the white inner pouch. Do not open the white inner pouch. The pouch is designed to keep the dry sodium chlorite compartmentalized until it hits water.

Step 2. Add the pouch to an opaque (not clear) 20-gallon drum filled with 20 gallons of water. This is the single point where the parent-hub product page trips people up: its activation walkthrough was written for the 5-gallon protocol, not the 20-gallon one. For the 3.36oz packet, the container is the opaque 20-gallon drum (SKU 185-20GC) and the water volume is 20 gallons.

Step 3. Agitate for one minute at 15-minute intervals until full activation at one hour, a total of five agitations. Allow one hour before use to ensure the solution reaches full strength. Keep temperature between 20 and 25 degrees Celsius.

Step 4. Record the activation date on the drum. Use stored formula within 15 days of activation, and dispose of stored formula after 15 days. For surface disinfection, apply at 100 ppm and hold a 10-minute exposure time. The solution goes on via mop, sprayer, or sponge, with visibly soiled surfaces pre-cleaned first.

Dosing math for multi-room facilities

This is the question a head grower actually has: how many 20-gallon batches does my facility burn per turnover, and how do I schedule the mixing so nothing expires before I use it.

Work a concrete example. A 5,000-square-foot facility runs 4 flower rooms, 2 veg rooms, and 1 mother room, seven rooms total. Surface disinfection at 100 ppm on hard, non-porous surfaces (benches, trays, grow beds, drop-down hoses, walls) in a mid-size room commonly draws on a few gallons per room depending on surface area and how you apply it. One 20-gallon batch can cover several rooms in a single turnover if you are applying by sprayer rather than flooding surfaces. The point is not an exact gallon count for your building; the point is that the 3.36oz packet lets you activate once and work a cluster of rooms off a single drum instead of stopping to mix a fresh 5-gallon batch between each room.

Then schedule against the 15-day window. A batch activated on a Monday is good through the Tuesday of the following week's week-two cutoff; practically, treat day 15 as the hard stop and plan a turnover cluster inside that window. If your flower rooms come down on a staggered calendar, mix one 20-gallon drum at the start of the turnover block, work the rooms that come offline inside the window, and log the date on the drum so the crew does not reach for expired solution. A documented activation-date-on-container practice, plus the SDS on file, is the minimum audit trail an operator can show a compliance auditor who asks what was used and when.

What the 20-gallon drum kit actually looks like

The 3.36oz packet does not work alone. The opaque 20-gallon drum (SKU 185-20GC) is the container, and it is opaque for a reason: activated ClO2 solution has to be kept out of direct sunlight, so a clear tank will degrade it. The label is explicit that the pouch goes into an opaque (not clear) container.

Dispensing is its own decision. A hand pump and a rotary pump are the two common ways to draw solution off a 20-gallon drum without tipping 160-plus pounds of liquid. Which you pick is a crew-ergonomics call, not a chemistry one.

Between activations, the drum is reusable. ProKure Solutions states plainly that its containers are reusable for future ProKure V treatments. You do not need a rinse-and-sterilize ritual between batches, but you do need to log the new activation date each time you refill. The reusability is part of the cost story: you buy the drum once and keep buying packets.

EPA registration and compliance for cannabis operators

If EPA compliance is your biggest worry, lead with the numbers, not the marketing. ProKure V is registered under EPA Reg. #87508-3-89334, EPA Est. #62788-AL-001. Those identifiers belong to ProKure V only. ProKure G carries a different registration (EPA Reg. #87508-2-89334) and ProKure D is not an EPA-registered product at all, so never attach V's registration to another product in your own documentation.

Two verbatim statements belong on your records. First: it is a violation of Federal Law to use EPA registered products in a manner inconsistent with the product labeling. Read the entire label and use strictly in accordance with precautionary statements and use. Second, the use restriction a reseller spells out: this item is to be used only for agriculture and cultivation applications. Both are approved compliance language, and both belong in your SOP binder.

For a multi-state operator, the registration is federal but your cannabis compliance is a separate stack. EPA Reg. #87508-3-89334 is the same number in every state. What varies state to state is the cannabis regulatory layer: pre-sale yeast-and-mold thresholds, allowable-input lists, documentation formats for auditors. Standardizing on one EPA-registered surface disinfectant across the footprint removes one variable from that stack. Your procurement team orders one SKU, your crews run one activation protocol, and your compliance file carries one SDS and one registration number for every facility.

Which ProKure V SKU do I need

The ladder exists so you do not over-buy or over-mix.

The 0.042oz packet makes 32 oz in a 32oz bottle. It is a single-bench spot-spray size. The 0.17oz packet makes 1 gallon in a reusable 1-gallon bottle, for single-room touch-ups. The 0.84oz packet makes 5 gallons in a reusable 5-gallon container, which is the workhorse for a single-room turnover. The 3.36oz packet, this page's SKU, makes 20 gallons in the opaque 20-gallon drum, for multi-room turnover where mixing 5-gallon batches one at a time slows the crew down.

Pick by volume and by the 15-day clock. If you cannot use 20 gallons inside 15 days, step down a size. If you are mixing three or four 5-gallon batches per turnover anyway, step up to the 3.36oz and mix once.

When you need ProKure G or D instead of V

ProKure V is the surface half of the system. It does not treat air. The related searches on this query (ProKure G, ProKure D, how to use ProKure G) show readers drifting toward the gas side, so here is the honest split.

ProKure V versus ProKure G. V is a liquid you mix and apply to hard, non-porous surfaces at 100 ppm. G is a fast-release gas, a deodorizing delivery system that works in 4 to 6 hours in an empty room and carries the required instruction "not for use with/on plants/crops/feed." You reach for G when the problem is odor or a fast air reset between cycles, not surface kill.

ProKure V versus ProKure D. D is a slow-release gas that provides ClO2 protection for up to 30 days and improves air quality and controls odors. D is not EPA-registered (the label carries the "not an EPA-registered product and not labeled for sale as a pesticide under 40 CFR" disclaimer). You reach for D for extended air-quality maintenance, not surface disinfection.

How growers stack all three across a cycle: V handles the between-cycle surface turnover on hard surfaces, G handles the fast empty-room air reset, and D maintains air quality over the weeks that follow. V is the only one of the three with a surface kill claim. Keep each product matched to its own approved claims and never pair V's mold-killing language with the gas products.

Frequently asked questions

The short version of everything above, in the questions operators actually type.

Related resources