ProKure D 1,000 Cubic Feet Coverage: The 10g Packet Sizing Guide
One 10g ProKure D packet covers up to 1,000 cubic feet for up to 30 days of continuous, low-level ClO2 release, which is the right size for a grow tent, a closet grow, or a small single-canopy room. It is humidity-activated and hangs on a reusable trifold 18 to 24 inches above the plant canopy, so it runs with plants in the room. ProKure D improves air quality and controls odors; it is not an EPA-registered product and not labeled for sale as a pesticide under 40 CFR. If your space is bigger than 1,000 cubic feet, you step up to the 50g or 95g packet, covered below.
This is the sizing page, written by GroClarity's biosecurity team under Dr. Bernie Lorenz, Chief Science Officer. You have a room and you want to confirm the 10g packet is the right SKU, understand how the 30-day release works at that volume, see the real price, and know what the EPA line means for your situation. That is what this page answers.
What 1,000 cubic feet actually looks like
Coverage is a volume number, not a floor-area number, so you size it with length times width times height. A lot of growers undershoot this because they think in square feet; the packet works the air in the whole room, so the ceiling height counts. Measure all three dimensions and multiply.
Here is how common spaces map to the 1,000-cubic-foot coverage of one 10g packet. A 4-foot-by-4-foot tent at about 7 feet tall is roughly 112 cubic feet, so a single packet covers it many times over, with headroom to spare. An 8-by-8-by-8-foot room is 512 cubic feet, still comfortably inside one packet. A 10-by-10-by-10-foot room is exactly 1,000 cubic feet, the top of a single 10g packet's range. A 12-by-10-by-8-foot room is 960 cubic feet, which also lands inside one packet. The pattern: most single tents, closets, and small rooms sit well under 1,000 cubic feet, so the 10g packet is the natural starter SKU for a single-canopy operation.
When your room runs past 1,000 cubic feet, do not stretch a 10g packet to cover it. Step up to the 50g packet, which covers up to 4,000 cubic feet, or the 95g packet, which covers up to 8,000 cubic feet. The 50g sizing page and the 95g sizing page carry those room-size decisions. For a room between sizes, round up to the SKU whose coverage meets or exceeds your measured volume, because an undersized packet in an oversized room is the most common reason coverage reads thin before the 30-day window is up.
A note on multiple spaces, because it trips up single-operators running more than one tent. Coverage is per enclosed air volume, so three separate 4-by-4 tents are not a 336-cubic-foot problem you solve with one packet floating between them; each sealed tent is its own air space and gets its own packet if you want protection inside it. If, on the other hand, those tents sit open in one 1,000-cubic-foot room that shares its air, a single packet sized to the room works. The test is simple: does the air move freely between the spaces? If yes, size to the whole volume. If no, size each space on its own. And for a room larger than one packet covers, the rule is to place pouches equally apart for even distribution rather than clustering them in one spot, so the ClO2 fills the volume uniformly.
The 10g ProKure D packet at a glance
The 10g packet is item 185-DE010C: a humidity-activated, slow-release ClO2 gas that covers up to 1,000 cubic feet for 30-day use, paired with a reusable trifold you keep and reload each cycle. Its approved product claims are the ones to use verbatim: it "improves air quality and controls odors" and "provides ClO2 protection for up to 30 days." Keep the "up to" on the 30 days, because the release depends on room humidity and the window is a maximum, not a guarantee.
Pricing is straightforward and real. The 10g single packet (SKU 185-DE010C) is $28.74 direct from ProKure. The 12-pack case (SKU 185-DE010C12) is $287.40, which works out to $23.95 per packet, a 17 percent case-pack saving over the single. For a single 1,000-cubic-foot room on a monthly re-treatment cycle, one case is roughly a year of coverage. Educate and size here on groclarity.com, buy and reorder on shop.groclarity.com, and pull the deep product detail, label, and SDS from prokuresolutions.com.
What the EPA status of ProKure D means for your room
This is the line that confuses shoppers, so it goes up front, plainly. ProKure D is "not an EPA-registered product and not labeled for sale as a pesticide under 40 CFR." Always read product labels before use. That is not a loophole or a downgrade; it is an accurate description of what D is and is not.
In plain English: ProKure D is a deodorizer and air-quality product. It is not sold as a pesticide, fungicide, or antimicrobial, and it carries no kill claims. That matters to a cannabis operator specifically, because a state inspector who asks what is running in the room wants an accurate answer, and the accurate answer for D is an air-quality and odor product, not a disinfectant. Stating it plainly is the compliant move; implying D kills mold or pathogens is both wrong and a label problem. If what you actually need is a registered fungicide to disinfect hard surfaces, that is ProKure V, the liquid hospital-type disinfectant, EPA Reg. No. 87508-3-89334, used at 100 ppm for a 10-minute contact time, which is suitable for use with plants in the room and leaves no residue. If what you need is a registered antimicrobial gas for a fast, between-cycle knock-down in an empty room, that is ProKure G, EPA Reg. No. 87508-2-89334, whose label states it is not for use with/on plants/crops/feed. D holds the air while the crop grows; V kills on surfaces; G resets the empty room. Keeping those three straight is the whole point, and it is why the disclaimer is a clarity tool, not a red flag. The ProKure D product label and SDS carry the full language.
ProKure D versus ProKure G at 1,000 cubic feet
This is the most important section on the page, because D and G both have a 10g SKU that covers about 1,000 cubic feet, and confusing them is the number-one sizing mistake for a small operation. They are built for opposite jobs.
ProKure D 10g is the slow, humidity-activated release: trace levels of ClO2 for up to 30 days, designed to run in an occupied room with plants present, hung above the canopy. It is the ongoing air-quality and odor layer for the live grow, and it is not an EPA-registered product. ProKure G 10g is the fast, water-activated release: a full dose of ClO2 that works in 4 to 6 hours for a between-cycle reset in an empty room. Its label states it is not for use with/on plants/crops/feed, so people and plants are out during treatment, and it is EPA-registered under 87508-2-89334. One competitor product listing even sells a 4,000-cubic-foot D SKU on a 1,000-cubic-foot search, telling shoppers the gas "covers up to 4,000 cubic feet," which is exactly the kind of size-and-product mismatch this page exists to prevent.
The simple rule: plants in the room, ongoing, pick D. Empty room, fast reset between cycles, pick G. Many facilities run both, G to reset the room between harvests and D to hold the air during the grow. If you came here wanting the empty-room knock-down, the ProKure G 1,000-cubic-foot sizing page is your page. If you need to disinfect surfaces before you hang D, start with ProKure V.
The reason the two products are not interchangeable comes down to how each one releases. ProKure D meters out trace amounts of ClO2 slowly as the pouch reacts with humidity in the air, which is exactly what makes it safe to run around a living crop for weeks: the concentration never spikes to a level that would be a problem for plants or people moving through the space on normal tasks. ProKure G does the opposite on purpose. It produces a fast, concentrated release that resets the air of an empty room in 4 to 6 hours, and that concentration is precisely why its label keeps people and plants out during treatment and calls for a one-hour ventilation gate before re-entry. Run G over a live crop and you have both a label violation and a real hazard; run D expecting a fast empty-room knock-down and you will be disappointed, because it was never built for that. Matching the release profile to the job is the entire sizing decision at 1,000 cubic feet, and it is the single thing the ranking pages leave a shopper to figure out alone.
How to use one 10g packet in a 1,000 cubic foot room
Activation follows the label, and this material does not replace it. Step 1: tear open the foil packet and remove the white inner pouch. Do not open the white inner pouch. Step 2: place a time sticker and a color sticker on the outside of the trifold, assemble the trifold by folding the flaps above the tray and pressing the button snaps together, then place the sponges in the recessed area of the tray and set the white inner pouch on top of the raised area. The plastic trifold is reusable for future ProKure D treatments, so you keep the housing and reload the pouch each cycle. Step 3: hang the trifold 18 to 24 inches above the plant canopy. ProKure D provides up to 30 days of ClO2 protection.
Two placement notes for a 1,000-cubic-foot space. With plants in the room, the 18-to-24-inch-above-canopy position is the one to use. In an empty room without a canopy to hang above, place the unit at a high point, because ClO2 gas is heavier than air and will settle and fill the volume from above. Either way, fans and air movers improve distribution across the room, which matters in a tent or closet where corners can go still. Log the activation date on your protocol sheet, not just on the sticker, so your replacement schedule and your audit trail both have the record.
One mistake to avoid at this size: do not open the white inner pouch, ever, and do not try to speed the release by cutting or agitating it. The slow, metered release is the entire design of the 10g D packet, and defeating it does not give you faster protection, it gives you an uncontrolled release that no longer matches the up-to-30-day window the coverage is built around. If you need faster, that is a signal you wanted ProKure G, not a modified D packet. Keep the packet intact, hang it per the label, and let the humidity-activated chemistry do its job over the full window.
The 30-day cycle and cost per day for a 1,000 cubic foot grow
The number a small operator and an owner both want is cost per day of protection. A single 10g packet at $28.74 across its up-to-30-day window is about $0.96 per day of continuous ClO2 air-quality protection for a 1,000-cubic-foot room. Buy the 12-pack case at $287.40 and the per-packet price drops to $23.95, which is about $0.79 per day on the same monthly cycle, and the case covers roughly a year of monthly re-treatment for one room.
Framed against the risk, that is a small line item. One positive pre-sale mold test on a mature crop can cost the whole batch, because smokable flower cannot be rinsed and there is no compliant wash that makes it saleable again. Measured against a loss like that, under a dollar a day to hold air quality in the room is prevention, not expense. The owner who treats the packet as a cost to trim is underwriting the larger loss; the one who treats it as insurance is buying down the odds of the single event that actually hurts.
There is also a planning point in the 30-day window that the single-packet math hides. The window is a maximum, up to 30 days, not a guarantee, because the release depends on room humidity; a drier, aggressively dehumidified space will meter the pouch out more slowly, and a very humid one faster. So the practical move is to schedule the replacement before the window closes rather than waiting for the pouch to fully expire, which would leave a gap where ClO2 output has tapered off. On a monthly cadence, a 12-pack case lines up cleanly: one packet per month per 1,000-cubic-foot room, with the case covering roughly a year. For a multi-room operation, case-pack economics across the 10g, 50g, and 95g sizes are a procurement conversation; request a quote from GroClarity for a footprint. The air-quality management pillar carries the broader program this packet fits into.
Where growers use the 10g packet, and the documentation you keep
The 10g ProKure D packet suits greenhouses, indoor and outdoor agricultural facilities, and hydroponic facilities, per the product's use areas. In practice, those use areas cover almost every small enclosed space a single-canopy grower runs, which is why the 10g is the SKU most new ProKure D customers start with before they size up or buy a case. For the single-canopy operator this page is written for, that means a grow tent, a closet grow, a small mother room, a small dry or cure room, or a storage area adjacent to the flower room, any space in the 500-to-1,000-cubic-foot range that needs ongoing air quality with product present.
For compliance, keep the documentation on file: the ProKure D product label, the SDS, and the SKU sheet, all available from prokuresolutions.com, alongside your own activation-and-replacement log. Because D is not an EPA-registered pesticide, the record you keep is the air-quality-and-odor description plus your usage log, which is what a state inspector will want to see when they ask what the product in the room is. Do not reach for a kill claim or an EPA registration number for D, because it has neither; describing it accurately as an air-quality and odor product is both correct and the safer answer at audit. A missing SDS at audit time is an avoidable failure, so pull it once and keep it with your protocol, and log each packet's activation and planned replacement date as you go so the binder assembles itself.
When you are ready, buy the 10g packet or the 12-pack case on shop.groclarity.com, pull the label and SDS from prokuresolutions.com, and talk to a ProKure specialist at GroClarity for sizing help on your specific room. If your room turns out to need more than one packet, or if you want to pair D with a ProKure V surface disinfection and a ProKure G empty-room reset into a full between-cycle protocol, that is a sizing-and-protocol conversation the GroClarity team can walk room by room. The Science of Biosecurity.
Frequently asked questions
How much space does one 10g ProKure D packet cover?
One 10g ProKure D packet (SKU 185-DE010C) covers up to 1,000 cubic feet for up to 30 days of continuous, low-level ClO2 release. Size it by volume, length times width times height, not floor area, because the gas works the whole room including the ceiling height. Most single tents and small rooms sit well under 1,000 cubic feet, so one packet is the right starter SKU for a single-canopy space.
How many 10g packets do I need for a 4x4 grow tent?
One. A standard 4-foot-by-4-foot tent at about 7 feet tall is roughly 112 cubic feet, which is far under the 1,000-cubic-foot coverage of a single 10g packet. A single packet covers it with room to spare, so you do not need to double up. If you run several tents, size each enclosed space on its own volume rather than adding them together, unless they share open air.
Can I use ProKure D 10g with plants in the room?
Yes. ProKure D is designed as an ongoing air-quality and odor product that runs with plants present. Follow the label activation steps and hang the reusable trifold 18 to 24 inches above the plant canopy for up to 30 days of ClO2 protection. It is not an EPA-registered product and not labeled for sale as a pesticide under 40 CFR, so it is an air-quality product, not a disinfectant you apply to the plant. Always read the product label first.
How much does the 10g ProKure D packet cost?
The 10g single packet (SKU 185-DE010C) is $28.74 direct from ProKure. The 12-pack case (SKU 185-DE010C12) is $287.40, which works out to $23.95 per packet, a 17 percent case-pack saving. For a single 1,000-cubic-foot room on a monthly cycle, the case is roughly a year of coverage, or about $0.79 per day versus $0.96 per day buying singles.
What is the difference between ProKure D 10g and ProKure G 10g at 1,000 cubic feet?
ProKure D 10g releases trace ClO2 slowly for up to 30 days and runs in an occupied room with plants present; it is not EPA-registered. ProKure G 10g releases a full dose of ClO2 quickly, working in 4 to 6 hours for a between-cycle knock-down in an empty room, and its label states it is not for use with/on plants/crops/feed. G is EPA-registered under 87508-2-89334. Plants in, ongoing: D. Empty room, fast reset: G.
Is ProKure D an EPA-registered pesticide?
No. ProKure D is not an EPA-registered product and not labeled for sale as a pesticide under 40 CFR. It is a deodorizer and air-quality product that improves air quality and controls odors, with no kill claims. If you need an EPA-registered fungicide for hard surfaces use ProKure V (EPA Reg. No. 87508-3-89334); if you need an EPA-registered antimicrobial gas for an empty-room reset use ProKure G (EPA Reg. No. 87508-2-89334). Always read the product label before use.
Related resources


