The ProKure G Room Preparation Checklist for Grow Facilities

Before you open a ProKure G packet, the room has to be empty, clean, measured, and sealed. That prep is the difference between a treatment that works and one that wastes a packet or voids the label. This checklist covers the setup a facility manager does first: confirm no people, plants, or pets are in the space, pre-clean surfaces so the gas is not eaten by debris, run the coverage math to size the packet, make the HVAC call, post caution placards, and plan the 4-to-6-hour dwell plus one-hour ventilation before re-entry. ProKure G is an unoccupied-space product, "Not for use with/on plants/crops/feed." Activation itself lives on the how-to-activate guide; this is everything before it.

Confirm the room is empty of plants, people, and pets

This is the step that prevents a six-figure mistake, so walk the room, then walk it again.

The manufacturer's rule is unambiguous: the ProKure G fast gas is for unoccupied spaces, with no people or plants in the space during treatment. That means more than glancing at the grow benches. Check clone racks, propagation trays, and any mother plants tucked in a corner. Check adjacent rooms that share a return air path, because gas can migrate through shared HVAC to a flowering room next door. Check for pets, which small facilities often have on site. ProKure G carries the verbatim restriction "Not for use with/on plants/crops/feed," so a single overlooked tray is a plant-kill exposure. If what you actually want is a plants-present job, ProKure G is the wrong product and a residue-free liquid like ProKure V is the plants-in-room answer.

Pre-clean surfaces so the gas is not wasted

ClO2 is an oxidizer, and organic debris consumes it, so a dirty room is a weak treatment.

Remove harvest waste, trim scraps, and root balls. Sweep the floor, empty drain pans, and pull empty reservoirs. Wipe visible biofilm from benches and walls with the liquid disinfectant and let surfaces dry before the gas phase, because standing water and slime give the gas something to burn through before it reaches the air you care about. The order matters: liquid surface work first, dry down, then the gas. A room that starts clean lets the full 4-to-6-hour cycle do air and surface deodorizing work instead of spending itself on sludge.

Measure the room and size the packet

Coverage is published in cubic feet, so the third dimension is the one people forget.

Measure length times width times height in feet and multiply for cubic feet. Match that to the packet: a 10g packet covers about 1,000 cubic feet and a 25g packet covers about 2,250 cubic feet, both paired with the reusable gas dispersion cup. A 10 by 10 room at a 10-foot ceiling is 1,000 cubic feet, a clean single 10g fit; a 20 by 20 room at 10 feet is 4,000 cubic feet, which needs two 25g packets spaced apart rather than one in a corner. For irregular rooms with mezzanines or split ceilings, measure each volume and sum them, and when in doubt size up, because an undersized room is an undertreated room.

Plan the HVAC decision and seal the room

The duct decision is a fork, and the manufacturer states it plainly.

If the ventilation system is solely for the space being treated, you can run it to circulate the gas. If the system is shared with other rooms, turn it off and close the ducts, because you do not want ClO2 traveling to a room with plants or people in it. Seal return vents with tape, plastic sheeting, or magnetic covers, and physically tag the exhaust fan switch so no one flips it mid-cycle. For a multi-room MSO, the shared-return-air path is the single biggest risk, so verify isolation before anything else.

Placement, placards, and the re-entry plan

Where the packet sits and how the room is marked are both prep steps, done before activation.

ClO2 gas is heavier than air, so place the activated product in a high, central, stable location, no closer than 18 to 24 inches from fabrics, leather, electronics, mirrors, metals, or plated surfaces, which concentrated gas can damage. Move anything sensitive out of that buffer first. Post caution placards on every door, including interior connecting doors, and write the activation time and the safe re-entry time on each one; for multi-shift facilities, add a lockout tag so an incoming crew cannot walk in. Then stage the re-entry plan before you start the clock: confirm the exhaust fans work, confirm the ventilation path is clear, and assign the person who returns to ventilate. PPE is not required for the unoccupied treatment itself, but chlorine dioxide gas can irritate the respiratory tract if the label is not followed, so the placards and the ventilation discipline are the safety system.

Timing, from activation to safe re-entry

Once the room is prepped and the packet activated, the clock is simple and non-negotiable.

Allow at least 4 to 6 hours of dwell for the gas to work. Then ventilate and turn the lights on for one hour before re-entry. So the earliest safe return is roughly 5 to 7 hours after activation, depending on your dwell. Do not re-enter during the ventilation hour, and do not trust a timer alone over the posted placard times. If odors reappear after re-entry, repeat the treatment. For the activation steps themselves, the ProKure G activation guide picks up where this checklist ends.

EPA compliance checkpoints and common mistakes

The prep is also your compliance record, which is the Q40 worry made concrete.

Before activation, verify six things and log them: the product is used for its labeled purpose, the dosage matches the room's cubic footage, the space is unoccupied with no people, plants, or pets, the placards are posted, the ventilation and re-entry plan follows the label, and you have recorded the activation date, room, packet SKU, and operator name. ProKure G is EPA Reg. No. 87508-2-89334, and it is a violation of Federal Law to use the product in a manner inconsistent with the labeling, so read the entire label and use strictly in accordance with the precautionary statements. The mistakes that void a treatment are predictable: activating with plants in a room on shared HVAC, under-dosing by ignoring ceiling height, skipping the pre-clean, re-entering before the ventilation hour, and reusing placards without updating the times. For how this prep plugs into the full turnover, the mold prevention protocols and air quality management guides carry the rest. Order ProKure G on shop.groclarity.com, pull the label and SDS from prokuresolutions.com, and call GroClarity at 866.206.1301 for a facility SOP.

FAQ

The questions facility managers ask while prepping a room for ProKure G.

Related resources