How often should you run ProKure G between grow cycles?
Run one ProKure G fast-release gas treatment per room, per turnover, after the room is stripped and surface-cleaned and before you re-plant. That once-per-turnover pass is the baseline cadence for a standard flower-room reset, not a ceiling. You add treatments when a trigger fires: a positive mold or yeast test on the last harvest, HVAC service, a new strain or clone source, or a room that sat empty past your normal window. Allow 4 to 6 hours for the treatment, then ventilate one hour before re-entry. The product label governs allowed use, so read it.
That is the short version a head grower can act on today. The rest of this guide is the reasoning, the turnover timeline the cadence attaches to, how it changes by facility type, the triggers that justify an extra pass, and how to prove to a state auditor that the cadence actually worked. GroClarity educates on the cadence here; you reorder ProKure G on shop.groclarity.com and pull the master label and SDS from prokuresolutions.com for your compliance file.
The short answer on cadence
One treatment per room turnover is the number most operators are looking for, and it holds for a standard empty-room reset between harvests.
Here is why the "how often" question has no clean answer anywhere in search results. The manufacturer product page walks you through activating a single treatment in four steps, then stops. Its only frequency instruction is three words long: "Repeat treatment if odors reappear." That is a reactive trigger, the kind you act on after you smell a problem, not a cadence you can write into a turnover SOP. For a grower who wants to schedule treatments across a harvest calendar, "repeat if odors reappear" is the end of the help, not the start of it.
So treat the baseline as proactive, not reactive. You run ProKure G once during the turnover window on every room you are resetting, because the point of a between-cycle treatment is to reset the air and reach the surfaces a wipe-down misses before the next crop goes in, not to wait until odor tells you mold already took hold. "Once per turnover" is the floor. You scale up from it when a specific trigger gives you a reason.
There is one more reason once-per-turnover is the right default rather than something more aggressive. ProKure G is a point-in-time air treatment, not a residual one. It does its work during the dwell window and then dissipates, which is exactly what makes it safe to re-enter the room and re-plant on the same turnover day. A product that does not leave a residual is not a product you run continuously; you run it at the moment the room is empty and the next crop is about to go in, which is once per turnover. If you want continuous, low-level air protection during the grow, that is a different product and a different cadence, covered later in this guide.
What the ProKure G product label controls
The label, not this page and not a forum, is the authority on allowed use frequency. ProKure G is EPA-registered, and the product page states the constraint in plain federal language: it is a violation of Federal Law to use EPA-registered products in a manner inconsistent with the product labeling. Read the entire label, follow the dwell and ventilation windows, and confirm the use sites. When you build a cadence into an SOP, cite the label as the controlling document so the SOP and the registration never drift apart.
One practical note for SOP writers: the label is the one input to your cadence that can change without you changing anything. The EPA periodically reviews registered products, so the version of the label you filed two years ago may not be the version that governs today. Pull the current master label from prokuresolutions.com when you set the cadence and again at each annual SOP review, and date the copy in your file. That habit is the difference between a cadence that is defensible at audit and one that cites a document nobody can find.
Where ProKure G fits in a between-cycle turnover timeline
A between-cycle reset is a sequence, and ProKure G lives at one specific phase of it. Map the whole thing so the treatment lands where it does the most good.
Strip the room first. Pull the spent plants, media, and any removable equipment, and get the gross debris out. Then clean surfaces: this is a ProKure V job, not a ProKure G job. ProKure V is the EPA-registered liquid Hospital-Type Disinfectant that handles hard, non-porous surfaces at its label concentration, is suitable for use with plants in the room, and leaves no residue. Benches, trays, tools, and walls get the liquid. Do not reach for the gas to clean a surface you can wipe.
ProKure G enters at the air-and-void phase. Once the room is stripped and the reachable surfaces are cleaned, the deep-penetrating ClO2 vapor fills the room volume and reaches the places a sprayer never touches: HVAC returns, under-bench voids, the corners of a sealed flower room. A 25g packet covers 2,250 cubic feet; a 10g packet covers 1,000. Place the packet, leave, and let it work.
The treatment window is fixed by the label: allow at least 4 to 6 hours for the system to work, then ventilate and turn the lights on for one hour before re-entry. People, pets, and plants are out for the duration, which is the whole reason the gas treatment belongs in the empty-room part of the turnover and not during the grow. Plan the turnover calendar around that window. A 4-to-6-hour dwell plus a one-hour ventilation means a room can be stripped and cleaned in the morning, treated through the afternoon, ventilated in the early evening, and ready to re-plant the next morning. That sequence is what keeps a reset inside roughly a 24-hour window instead of stretching turnover into the multi-day stall that bleach-and-air-out protocols create.
The order of operations matters as much as the cadence. Gas before you clean and you are treating a room still full of debris and spent media, which gives the pathogen load somewhere to hide. Clean before you gas and the vapor is working against a much smaller target, reaching the voids your crew could not. The sequence is strip, then surface-clean with the liquid, then gas the air and the voids, then ventilate, then re-plant. ProKure G sits in the middle of that line, and running it out of order is the most common way a turnover treatment underperforms. After re-entry, the acute reset is done, and the room is ready for the next phase of ongoing air management, which is where ProKure D comes in later in this guide.
Cadence by facility type
The once-per-turnover baseline is the same rule everywhere, but the packet count, the room count, and the scheduling change with the operation.
A single-room or small multi-room grow runs the simplest version: one packet sized to the room (10g for up to 1,000 cubic feet, 25g for up to 2,250) during each turnover, scheduled into the day or two the room is empty. The crew does not evacuate the building for fumes the way a bleach protocol forces, because the room is sealed and empty during the dwell and ventilated before anyone re-enters. That is what lets a reset fit inside a single turnover day.
A multi-room commercial flower operation multiplies the baseline by rooms and by harvests per year. A 2,250-cubic-foot flower room takes a 25g packet per turnover; size the packet count to each room's volume rather than guessing, and if your rooms vary, the per-room math is worth running once and writing down. Standardize the per-turnover rule, then let room count and cycle count set your annual packet quantity.
MSO multi-state SOP: standardizing frequency across facilities
A Cultivation Director at a multi-state operator needs one cadence rule that survives a copy-paste across every facility, and once-per-turnover is exactly that kind of rule. It does not depend on local water chemistry or a specific room layout. Write it as: one ProKure G treatment per room per turnover, sized to room volume, during the empty-room window, with the label as the controlling document and a defined list of repeat triggers. Then each facility references its own state cannabis program for any added requirement on top of the federal registration. One product, one cadence rule, one data trail, with state-specific overlays confirmed per jurisdiction.
Mother rooms and clone rooms are the exception worth naming, because they are rarely fully empty. You cannot gas a room that has plants in it, so the between-cycle treatment schedule for a perpetual mother or clone room is driven by the windows when the room is actually cleared, not by a flower-room harvest calendar. Plan the ProKure G pass for a scheduled clear-out, and lean on ongoing air management the rest of the time.
Room volume is the input that most often gets guessed and should not be. The coverage is specific: a 25g packet is rated for 2,250 cubic feet, a 10g packet for 1,000. Measure the room, do not eyeball it, because a 25g packet in a 4,000-cubic-foot room is an under-treatment dressed up as a treatment, and two 10g packets scattered without regard to placement is not the same as one correctly sized pass. For rooms that fall between the standard sizes, size up rather than down and place packets for even coverage. If you are standardizing across rooms of different volumes, run the cubic-foot math once per room type and write the packet count into the SOP so the crew is not recalculating on turnover day.
Triggers to repeat a ProKure G treatment mid-turnover
The once-per-turnover baseline covers the routine case. These triggers tell you when one pass is not enough, and they are the part of the cadence conversation no ranking page spells out.
Odor reappearance is the manufacturer's stated trigger, and it stands: if odor comes back, repeat the treatment. Treat it as the floor of the trigger list, not the whole list.
A positive mold or yeast test on the prior harvest from the same room is a hard trigger. If the last crop out of a room failed or flirted with a state yeast-and-mold threshold, that room earned an extra pass before the next crop goes in, because the pathogen load that showed up in the flower did not evacuate on its own. If you are responding to a mid-cycle positive test rather than a between-cycle reset, that is a different protocol with a different intent, and it deserves its own walkthrough.
HVAC service, a filter change, or any ductwork access reopens the air system you just treated, so schedule a treatment after the work is done rather than before. The gas reaches the HVAC returns and the duct voids on the original pass; the moment a technician opens that system, you have introduced outside air and hands into a space you had controlled, and the only way to restore the reset is to run it again.
New strain or new clone-source introduction brings an unknown microbial history into the room. You do not know what traveled in on that new genetic, so a reset before it goes in protects not just that room but the rooms it will share air with through a common handling path. A room that sat empty longer than your standard turnover window has had time to accumulate dust and spore load on surfaces you cleaned weeks ago, so the original pass no longer reflects the room's current state; re-treat before re-planting instead of trusting a treatment that has gone stale.
Write these triggers into the SOP as a named list, not as crew judgment calls. "Re-treat after HVAC service" is a line an auditor can check and a new hire can follow. "Re-treat when it seems necessary" is neither. The triggers are what turn a single baseline number into a cadence that responds to what actually happens in a working facility.
How to prove the cadence is working
A cadence you cannot prove is a cadence an auditor will not credit. Build verification into the schedule, not as an afterthought.
Pull air samples before and after treatment on a representative schedule so you have a measured delta, not an assumption. Add surface swabs on the high-risk zones (drains, HVAC returns, the spots that failed before) to confirm the surface-plus-air approach landed. The point is a documented trail, not a single reassuring reading.
Tie the whole thing to your state's mandated total yeast and mold load thresholds. Those numbers vary by state and change over time, so confirm the current threshold with your state regulator rather than a figure you remember, then log your pre-sale results against it. For the audit file, keep the treatment record (product, packet size, room, date, operator), the ventilation and re-entry times, and the test results that bracket the treatment. That binder is what turns "we run ProKure G every turnover" into a claim an inspector can follow line by line.
Verification also closes the loop on the cadence itself. If post-treatment air and surface results come back clean turnover after turnover, your once-per-turnover baseline is validated and you leave it alone. If a specific room keeps trending toward its threshold despite a correct pass, the data is telling you that room needs a trigger-based second treatment, or that something upstream (an HVAC return, a recurring source) is reseeding it between crops. The cadence is not a number you set once and forget; it is a baseline you confirm with measurement and adjust per room when the plates say so. GroClarity offers air-testing support to build exactly that data trail, which is the piece the manufacturer and reseller pages leave entirely to the grower.
Pairing ProKure G with ProKure D between cycles
ProKure G and ProKure D are the natural cadence pair, and almost nothing in search results says so. G is the acute turnover treatment; D is the ongoing air-quality layer that follows it.
G handles the fast, empty-room reset: deep-penetrating ClO2 vapor, 4 to 6 hours, then ventilate. It is a point-in-time event on the turnover calendar. Once the room is reset and re-entered, the acute job is finished.
D picks up where G leaves off. ProKure D is the slow-release gas that provides ClO2 protection for up to 30 days, improving air quality and controlling odors at low-level vapor while the room is occupied. It carries the verbatim disclaimer that it is not an EPA-registered product and not labeled for sale as a pesticide under 40 CFR, and it makes no kill claim; it is an air-quality product, not a disinfectant. A workable combined cadence looks like this: ProKure G on turnover day in the empty room, then ProKure D deployed as the room comes back online and through the early veg window, replaced before each up-to-30-day window closes. G resets, D maintains.
You might reasonably push back here: if I am treating every turnover with G, why pay for a second product at all? The honest answer is that the two do different jobs on different timelines, and skipping D does not break the G cadence, it just leaves the room without air support during the stretch when plants are present and G legally cannot run. Between-cycle resets are events. The weeks in between are a gap. D fills the gap that G, as an empty-room treatment, is not allowed to touch. For a small single-room operation on a tight budget, running G alone at turnover is a defensible choice; for a facility that has failed a yeast-and-mold test before, the continuous layer is cheap insurance against repeating it.
EPA registration, label compliance, and common cadence mistakes
The Phase 1 worry that drives half of these questions is EPA restrictions, so put the compliance facts on the page rather than burying them.
ProKure G is EPA-registered as a fast-release chlorine dioxide gas; an industry reseller states it plainly, noting "ProKure® G fast-release gas is EPA-registered." The verbatim federal-law disclosure from the product page is the governing text: it is a violation of Federal Law to use EPA-registered products in a manner inconsistent with the product labeling, so read the entire label and use strictly in accordance with it. The label also carries the use restriction verbatim: "Not for use with/on plants/crops/feed. Always read product labels before use." That line is specific to ProKure G, and it is the reason the treatment is an empty-room event. The cadence guidance that governs your facility lives on the actual label, so keep a current copy in the compliance file and treat it as the final word.
A few cadence mistakes show up again and again. Treating too infrequently, meaning only after a positive test, turns a preventive product into a reactive one and defeats the point of a between-cycle reset. Treating with plants present violates the label, because ProKure G is not for use with or on plants. Skipping the 4-to-6-hour dwell cuts the treatment short before the gas has done its work. Skipping the one-hour ventilation before re-entry is a crew-safety failure, not a shortcut. Each of these is avoidable by writing the label windows into the SOP and holding the crew to them.
FAQ
The questions below are the ones growers and ops directors ask before they write a turnover schedule.
How often should ProKure G be used between grow cycles?
Once per room, per turnover, is the baseline: run one correctly sized treatment after the room is stripped and surface-cleaned and before you re-plant. Add treatments when a trigger fires, such as a positive mold test, HVAC service, a new strain, or a room left empty past your normal window. The product label governs allowed use frequency, so build the cadence around it.
Can you use ProKure G with plants in the room?
No. The ProKure G label carries the verbatim restriction "Not for use with/on plants/crops/feed," which makes it an empty-room treatment. People, pets, and plants are out during the 4-to-6-hour dwell, and you ventilate for one hour before re-entry. For protection while plants are present, ProKure D provides low-level ClO2 air quality for up to 30 days, and ProKure V handles surfaces and is suitable for use with plants in the room.
How long does a ProKure G treatment take?
Allow at least 4 to 6 hours for the system to work, then ventilate and turn the lights on for one hour before re-entry. That roughly 5-to-7-hour total window is what lets a between-cycle reset fit inside a single turnover day rather than stretching across several.
Do you need to treat every room every turnover?
Treat every room you are resetting for a new crop. The once-per-turnover baseline is a prevention cadence, not a reaction to a problem, so the default is to run it on each room during its empty-room window rather than waiting for a reason. Rooms that are rarely empty, like perpetual mother or clone rooms, get treated on their scheduled clear-outs instead.
What is the difference between ProKure G and ProKure D for between-cycle use?
ProKure G is the fast-release gas for the acute turnover reset: deep-penetrating ClO2 vapor, 4 to 6 hours, empty room only. ProKure D is the slow-release gas that improves air quality and controls odors for up to 30 days while plants are present, with no kill claim and the 40 CFR non-pesticide disclaimer. G resets the room, D maintains the air between resets.
Is ProKure G EPA-registered?
Yes. ProKure G is EPA-registered as a fast-release chlorine dioxide gas. Because it is a registered product, federal law requires you to use it strictly in accordance with the product label, which is also the document that governs allowed use frequency for your facility.
If you have not activated ProKure G before, the four-step foil-pouch process and the coverage math live on their own GroClarity pages, and the reactive mold-response protocol is a separate walkthrough because it is a different intent entirely.
Related resources


