You bought ProKure V, you have a packet in your hand, and you need one number: how much water. Here it is, straight from the ProKure V label (EPA Reg. No. 87508-3-89334). The 3.36oz (95.2 gram) packet makes 20 gallons at 100 ppm. The 0.84oz (23.8 gram) packet makes 5 gallons. The 0.17oz (5 gram) packet makes 1 gallon. The 0.042oz (1.19 gram) packet makes 1 quart. One packet per the listed water volume, in an opaque (not clear) container, agitated one minute at 15-minute intervals until full activation at one hour. Mix the right ratio and you are on-label. Guess, and you are off-label.

You probably think you can eyeball it. On a regulated disinfectant, you can't.

Most grow-room sanitation gets done by feel. A cap of this, a glug of that, close enough. ProKure V is not that kind of product, and the reason is printed on the label. It is a chlorine dioxide generator with an EPA registration number, 87508-3-89334, and the label is a legal document. The label states one exposure condition for hard-surface disinfection: 10 minutes at 100 ppm. Hit a different concentration because you poured in the wrong amount of water and you are no longer following the label.

That matters more in cannabis than almost anywhere else, because the people who inspect your facility can ask to see what you used and how. ProKure's own FAQ is blunt on where V is approved: "No, ProKure V is approved to use on hard, non-porous surfaces." The concentration is half of "following the label." The other half is the water volume that gets you there. This page exists to remove the guesswork from that second half.

The four SKUs are not interchangeable scoops of the same thing diluted differently. Each packet holds a measured dry charge sized to one specific water volume. You do not scale a 0.84oz packet up by adding more water to stretch it; you grab the SKU that matches the batch size you need.

The four ProKure V SKUs and the water each one takes

These are the label volumes for a 100 ppm solution, which is the surface-disinfection concentration. Read them as fixed pairs.

ProKure V SKUDry weightWater for 100 ppmReady-to-use yieldTypical batch---------------3.36 oz packet95.2 g20 gallons (75.7 L)20 galWhole-room turnover, multi-station day0.84 oz packet23.8 g5 gallons (18.9 L)5 galOne room, benches, trays, tools0.17 oz packet5 g1 gallon (3.7 L)1 galTrim table, tool dip, spot work0.042 oz packet1.19 g1 quart (946 mL)1 qtSmall surface, single station

Pick the SKU, add exactly that water, and you have a 100 ppm batch. The procurement math falls out of the same table: a 12-pack of 0.84oz packets yields 60 gallons of ready-to-use disinfectant, because each packet is a clean 5-gallon unit. That is the number a QA lead or an owner wants before approving the next purchase order, and it is the number the product listings on retailer pages bury inside a cart. GroClarity publishes it here so purchasing can do case-level yield without opening a PDF.

The label also gives you two step-downs from a 100 ppm stock if your use calls for a lower concentration: 20 ppm is one part stock to four parts water (1:5), and 5 ppm is one part stock to nineteen parts water (1:20). The 5 ppm dilution is the food-contact sanitizer and fruit-and-vegetable rinse concentration; the 20 ppm is a sanitizing step for hard surfaces. Use those ratios only for the applications the label names them for.

Two mechanical details from the label keep the batch honest. First, use an opaque container, not a clear one, because chlorine dioxide is light-sensitive and sunlight degrades the solution. Second, the product needs a full hour to reach strength: add the pouch, agitate for one minute, repeat at 15-minute intervals for a total of five agitations across one hour, and hold the temperature between 20 and 25 degrees Celsius. A batch you mix and use at minute ten is not yet at label concentration, which is a quiet way to end up off-label without ever touching the water ratio.

Why the ppm, not the packet, is the thing that actually works

Here is the part most pages skip. ProKure V is not a disinfectant sitting in the packet waiting to be watered down. The dry charge is a chlorine dioxide generator. Add water and a controlled reaction releases chlorine dioxide into solution over that one-hour activation window, which is why the water volume is fixed rather than a dial you can turn. Too little water and the solution runs hotter than 100 ppm; too much and it runs weak and may miss the 10-minute kill condition the label validates. The packet size and the water volume are a matched pair because the chemistry is a matched pair. That is also why you do not open the white inner pouch and do not combine it with acids: the generator is meant to react with water on your schedule, in your container, not on a shelf.

100 ppm versus 500 ppm, and why you should not invent the 500 ppm math

Here is where a lot of pages get sloppy. The ProKure V Cultivator label tables the activation volumes for 100 ppm. That is the surface-disinfection concentration, 10 minutes of contact time, and it is what the SKU-to-water pairs above produce. You will see "up to 500 ppm" referenced in the ProKure V safety data sheet, and a 500 ppm solution is a heavier-duty figure some operators reach for after an outbreak. But the per-SKU water volumes for 500 ppm are not on the Cultivator directions-for-use label in front of us.

So we are not going to print a 500 ppm column and pretend it came from the label. That would be exactly the off-label dilution this page is supposed to prevent. If you need a 500 ppm batch, pull the current ProKure V product label from the ProKure resources page and follow its stated volume, or call 866.206.1301 before you mix. The honest answer, the one the mall-kiosk version of this page would not give you, is that the number you want for 500 ppm belongs to the label, not to a blog post.

What you can take from this page with full confidence: the 100 ppm pairs above, the 1:5 and 1:20 step-downs, and the 10-minute-at-100-ppm contact condition for hard-surface disinfection.

The EPA registration you cannot skip

ProKure V carries EPA Reg. No. 87508-3-89334. That number is the product's legal identity, and it is the reason the mixing ratio is not a suggestion. Under federal pesticide law, using a registered product in a manner inconsistent with its labeling is a violation. The label puts it in plain language: "It is a violation of Federal Law to use this product in a manner inconsistent with the labeling. Read the entire label and use strictly in accordance with precautionary statements and use."

For a multi-state operator, the registration number is the same in every jurisdiction. The dilution is the variable, and it is the variable this page removes, so a Cultivation Director can hand the same batch standard to a crew in Alaska, Michigan, or Colorado. Standardized dilution is also an audit asset: it is a written, repeatable procedure you can show an inspector.

One separation to keep clean, because it protects both crop and license. ProKure V is suitable for use with plants in the room, on hard, non-porous surfaces. It is not for direct application to the plants themselves. ProKure's FAQ confirms both halves: "Can ProKure V be used with plants in the room? Yes." and "Can ProKure V be used directly on plants? No." Room-adjacent surface work, yes. On the plant, no. The 'Not for use with/on plants/crops/feed' disclaimer belongs to the gas product ProKure G, not to V; do not transplant it.

Fifteen days, then it's done

Activated ProKure V has a 15-day working life, and this belongs right next to the math because the moment you mix is the moment the clock starts. The label: use stored formula within 15 days of activation, record the activation date onto the container, and dispose of stored formula after 15 days. Store it dark, sealed, cool, and away from any food for human or animal consumption.

The practical version for a grow room: when you activate a 5-gallon batch from a 0.84oz packet, write the date on the bottle. Fifteen days later, that batch is spent whether you used it or not. This is why dose-on-demand with the right SKU beats mixing a giant stock you will not finish. A head grower running a laminated batch card at each station, activation date logged, is building the exact paper trail a compliance officer wants to see, which is the audit-ready habit the Steven ICP needs and no competitor page sets up next to the dilution number.

The unopened foil packets are a different, longer clock: ProKure states non-activated foil packets carry a 2-year warranty and keep working past that as long as the foil is not breached and storage is temperature-controlled. So the 15-day limit is the activated-solution clock, not the inventory clock. Buy the packets ahead, store them sealed, and start the 15 days only when you mix. That split is what lets a procurement lead stock a quarter of packets without burning shelf life, then dose on demand room by room.

The turnover math is where this stops being a chemistry lesson and starts being money. A facility manager loses three to five days of downtime per room turn when the sanitation step forces the crew out. A residue-free, plant-safe-in-room surface disinfectant that needs gloves at most during mixing does not force an evacuation, so the room can be worked and reset faster. Pair that with the SKU table and the batch log, and the between-cycle turn becomes a scheduled, documented procedure rather than a lost week, which is the whole reason a cultivator keeps V in the rotation alongside the air products.

Ready-to-use versus the packet concentrate, and the PPE question

Some of what ranks for this query is actually about ProKure V Ready-to-Use, a pre-mixed solution, not the packet concentrate you activate yourself. If you bought RTU, there is no math: it is already at concentration, so skip this page's calculator and use it as the label directs. The packets exist for operators who want dose-on-demand control, less storage volume, and a cleaner cost-per-gallon on high-turnover facilities.

On protective equipment, use the label and the manufacturer's stated position rather than guessing up or down. Per ProKure's FAQ: "At 100 PPM ProKure V does not require PPE, unless hands will come into contact with activated solution during dilution or application, at which time, protective gloves must be worn." Gloves during mixing and application, and read the full label for higher-concentration or heavy-remediation work. The dry, unactivated pouch is a different hazard class entirely (corrosive), so do not open the white inner pouch and do not mix with acids.

And the food-contact angle that makes V unusual in a grow: ProKure states V holds an NSF International certificate in the D2 category, meaning it is considered a sanitizer on surfaces not always requiring a rinse, and it leaves no residue. For infused-product kitchens and food-contact surfaces, that is the 5 ppm, one-minute sanitizer condition on the label. That combination, broad surface kill plus plant-safe-in-room plus no residue, is what bleach and quats cannot claim, and it is why a cultivator keeps V on the shelf for between-cycle turnover.

What you now have that you didn't when you landed here

You came in with a packet and a question. You leave with the exact water volume for your SKU at 100 ppm, the 1:5 and 1:20 step-downs the label allows, the 15-day activation clock, the PPE position in ProKure's own words, and the EPA registration number that makes all of it a compliance record instead of a guess. For the 500 ppm figure, you have the honest pointer to the current label rather than a number we made up.

When you are ready to restock, buy the SKU that matches your batch size at shop.groclarity.com, and pull the current label and SDS from prokuresolutions.com. For MSO-level procurement across all four SKUs, or a standardized dilution SOP across a facility grid, that is a conversation GroClarity has every week.

Related resources