ProKure V Contact Time: 10 Minutes at 100 ppm on Hard, Non-Porous Surfaces
To disinfect hard, non-porous surfaces, ProKure V must be used with an exposure time of 10 minutes at 100 ppm. In operational terms, contact time is the span the surface stays visibly wet with activated solution before you wipe, rinse, or let it air-dry. The timer only runs while the surface is wet. If a stainless bench dries in four minutes under grow-room conditions, your effective contact time was four minutes, not ten, and you did not hit the disinfection claim. The rest of this page is how to actually land the full ten minutes in a working room, and how to log it for a state audit.
What 10 minutes of contact time actually means
Contact time, dwell time, and exposure time are the same number on this label. The ProKure V directions set it at 10 minutes at 100 ppm for disinfection of hard, non-porous surfaces. There is no separate dwell figure hiding behind a different word.
The rule that trips up first-time users is the wet-surface rule. A disinfectant claim assumes the surface is continuously wetted for the whole interval. The moment the film dries, the clock effectively stops. In a lab at controlled humidity, a surface stays wet long enough on one pass. In a flower room at 75 to 82 degrees Fahrenheit and 50 to 60 percent relative humidity mid-turn, a thin spray coat on warm stainless can flash off well before ten minutes. So the operational version of the claim is not 'spray and walk away.' It is 'keep it visibly wet for ten minutes,' which on fast-drying surfaces means a heavier initial application or a re-wet pass at the five-minute mark.
Here is the part no retail listing reconciles, and it is the most common point of confusion. The same 100 ppm solution carries two different contact times for two different claims. Against SARS-CoV-2 on hard, non-porous surfaces, the kill claim is 30 seconds. For general disinfection of hard, non-porous surfaces, and as a fungicide against Aspergillus Niger, the exposure time is 10 minutes at 100 ppm. The dwell varies by the organism and claim, not by the product or the concentration. A grower who sees both numbers on a product page is not looking at a contradiction; they are looking at two separate label claims. When your target is general between-cycle disinfection or a fungal concern, plan around the 10-minute number, not the 30-second one.
The incumbent pages state the 10-minute sentence and stop there. The position-one result, a retailer collection page, repeats "To disinfect hard, non-porous surfaces, ProKure V must be used with an exposure time of 10 minutes at 100 ppm" once and never defines what contact time is or why it differs from the 30-second claim. That omission is the gap this page fills: a protocol-first definition written for someone standing in the room with a sprayer, not a lab-bench abstraction.
How to hit the full 10 minutes in a real grow room
The dwell does not start when you open the packet. It starts when the activated solution is on the surface, and getting to activated solution takes an hour.
First, the activation wait. After you mix a packet to 100 ppm, allow one hour before use to ensure the solution has reached full strength, agitating at the 15-minute intervals the label specifies. That hour is not part of the dwell; it is a prerequisite. If you need disinfected surfaces at 2 p.m., you are activating at 1 p.m. For the mixing procedure itself, follow our step-by-step guide on how to mix ProKure V to 100 ppm.
Second, application mode. Apply ProKure V by sprayer, mop, or sponge to the hard, non-porous surfaces you are treating. Do not fog it to try to shorten or shortcut the dwell; ProKure V should be applied by sprayer, mop, or sponge, not by fogging. Fogging is not an approved application mode for this product, so it is not a legitimate way to cover a room faster.
Third, keeping the surface wet. This is where the room beats you if you let it. On warm stainless benches and plastic trays in an active grow room, plan on a heavier wetting coat than you would use in a cool, humid lab, and budget a re-wet pass around the midpoint for any zone that is drying visibly. The surface must remain visibly wet for the full ten minutes for the claim to hold. No rinse is required afterward, and ProKure V leaves no residue, which is exactly why it fits a room where a crop stays present.
Sequence the whole thing and it is clean: activate and wait one hour, apply by sprayer or mop, start the ten-minute dwell, re-wet any fast-drying zone at five minutes, let it air-dry, then move to the next zone. The dwell is the fixed cost. Everything you do to the room before and after is scheduling around that fixed ten minutes.
Who and what can be in the room during the 10 minutes
The between-cycle turn is where the Facility Manager loses 3 to 5 days, so the practical question is what you can keep doing while the dwell runs.
Plants can stay. ProKure V is suitable for use with plants in the room, because the application is to hard, non-porous surfaces, not to the plant itself. It is not approved for direct application on plants. That distinction, surface disinfection with a live crop present and no residue left behind, is the reason a cultivator reaches for it over bleach or quats for cycle turnover, and it is a claim those alternatives cannot make.
People can stay too, within the PPE rule. At 100 ppm, ProKure V does not require PPE, unless hands will come into contact with the activated solution during dilution or application, at which time protective gloves must be worn. Respiratory PPE is not required when using ProKure V at 100 ppm. So the crew can continue working the room during the dwell; the only hard requirement is gloves for whoever is handling the solution.
Two boundaries to keep straight. First, this is a ProKure V answer, and it does not carry to the gas products. ProKure V is the liquid for surfaces with plants in the room; the gas-phase tools in the line have their own, different rules. Second, ProKure V is not approved for direct plant application or for fogging. Inside those boundaries, the ten-minute dwell is a low-disruption step, not a room evacuation.
For food-contact surfaces, the label carries a separate, shorter sanitizer claim at a lower dilution, which is a different use case from the 100 ppm disinfection dwell this page covers. If that is your scenario, our page on ProKure V food-contact surfaces walks the no-rinse sanitizer path.
Fitting the 10-minute dwell into a between-cycle SOP
The dwell is ten minutes per zone, but the real planning numbers are the activation hour and the 15-day activated shelf life.
Start with the shelf-life clock. Once activated, use the solution within 15 days. If any formula remains unused, pour it into a dark, closed or sealed container, store it in a cool, dark location away from sunlight and away from food, and use it within 15 days of activation. That means you batch to the work in front of you, not to a calendar month. Activating 20 gallons for a single bench pass wastes most of it on day 15.
Size the batch to the room using the packet grid. The four packet sizes make a quart, 1 gallon, 5 gallons, and 20 gallons respectively, all to the same 100 ppm. A quick tool-and-bench pass is a quart; a full room turn that will consume the volume the same week is a larger packet. Match the batch to the surface area you will actually wet during the activated window.
Then sequence a zone. Activate and wait one hour. Apply to zone one and start the dwell. While zone one dwells for ten minutes, you are staging zone two, not standing idle. Air-dry zone one, move on. The ten-minute dwell overlaps with staging and application elsewhere, so the room turn is gated by total wetted area and your activated-solution supply, not by a strict ten minutes multiplied by zone count. That overlap is the scheduling insight the retailer pages never surface, and it is what turns a dwell requirement into a manageable turn rather than lost days.
Logging the 10-minute dwell for a state audit
Procurement and QA leads need the dwell on paper, because a pre-sale compliance review wants proof, not a verbal assurance. The driver is real: as of June 2024, Aspergillus contamination has been responsible for 15 of California's 21 product recalls, which is why a Head Grower is documenting fungal-control steps at all.
Capture these fields per zone, per turn: date, room or zone ID, product and SKU plus lot number, activation time, application start time, dwell start time, dwell end time, and operator initials. The dwell start and dwell end are the two that matter most, because together they prove the full 10 minutes at 100 ppm actually ran. Tie the record to the EPA registration on file: ProKure V is EPA Reg. No. 87508-3-89334, and the label plus SDS belong in the same audit folder. For the registration and label detail, see our ProKure V EPA label reference.
Keep the compliance line attached to every kill-claim you log or publish. This material is not a replacement for the product label. It is a violation of Federal Law to use EPA registered products in a manner inconsistent with the product labeling. Read the entire product label and use strictly in accordance with precautionary statements and use. That sentence is not boilerplate to a state auditor; it is the frame that makes your dwell record defensible.
How the 10-minute dwell compares to other disinfectants
Contact time is not unique to ProKure V; every surface disinfectant carries one, and the category context explains why ten minutes is a reasonable, not a long, number. The CDC's guidance on chemical disinfectants documents that different chemistries need different exposure times to hit their claims, and that contact time is organism-dependent. Against that backdrop, a 10-minute dwell for a chlorine dioxide disinfectant on hard, non-porous surfaces is squarely in the normal band for a hospital-type product, and the 30-second SARS-CoV-2 claim is the fast end, not the rule.
Where the comparison gets practical is the trade-offs around the dwell. Sodium hypochlorite reaches high-level claims at strong concentrations; peer-reviewed work indexed in the literature reports sodium hypochlorite at 0.5 percent, which is 5,000 ppm, inactivating a surrogate on stainless steel at a 10-minute contact time. That is 50 times the 100 ppm ProKure V concentration for a comparable dwell window, and bleach brings residue and corrosion that a residue-free ClO2 solution does not. The dwell number alone is only half the picture; concentration, residue, and whether a crop can stay in the room are the other half. For the full head-to-head on dwell, residue, and PPE, see our ProKure V and bleach comparison.
The honest read: ProKure V does not win on dwell speed for general disinfection, where ten minutes is the spec. It wins on the combination a grow room needs, which is a real hospital-type disinfection claim at a low 100 ppm concentration, no residue, and plants allowed to stay in the room. That combination is the argument, not the stopwatch.
Frequently asked questions and next steps
Once the dwell is logged and the room is turned, the reorder and documentation path is straightforward. Keep the EPA label (Reg. No. 87508-3-89334), the SDS, and your dwell logs in one audit folder, and reorder through the GroClarity shop when you need more packets. For multi-facility standardization across state footprints, route to a ProKure specialist through the GroClarity contact form rather than buying ad hoc. The FAQs below answer the exact questions growers ask about the ten-minute number.
See product label for specific instructions and claims.
Related resources
Related resources


