ProKure V Contact Time: The 10-Minute, 100 ppm Dwell, and How to Hit It

ProKure V's label is specific: to disinfect hard, non-porous surfaces, it must be used with an exposure time of 10 minutes at 100 ppm, under EPA Reg. No. 87508-3-89334. That one sentence is the whole job, and it is where operators slip, because in a warm grow room the solution can dry on the surface before the 10 minutes are up. Contact time means the surface stays wet with 100 ppm solution for the full 10 minutes, not that you sprayed it once and walked away. This page explains what the label requires, how to actually hit the dwell on a real bench, how to confirm your concentration, and how to log it for an auditor.

What the label actually says

Precision matters because this is enforcement language, not marketing.

The sentence every operator memorizes

The label states that to disinfect hard, non-porous surfaces, ProKure V must be used with an exposure time of 10 minutes at 100 ppm. For SARS-CoV-2 specifically, the label time is 30 seconds at 100 ppm on hard non-porous surfaces. The 10-minute figure is the disinfectant dwell for the broader kill list, and it is tied to EPA Reg. No. 87508-3-89334.

Why "must be used with" is not optional

It is a violation of federal law to use an EPA-registered product in a manner inconsistent with its labeling. So "must be used with an exposure time of 10 minutes at 100 ppm" is the registered condition for the kill claim. Hit the concentration and the time and the claim holds; miss either and you are both off-label and, more practically, not actually disinfecting.

What contact time means in plain English

The term trips up anyone new to EPA disinfectants, so define it before executing it.

Dwell, contact, exposure: one idea

Dwell time, contact time, and exposure time are three names for the same thing: how long the surface must stay wet with the solution at the labeled concentration for the kill to occur. For ProKure V that is 10 minutes at 100 ppm on hard non-porous surfaces.

When the clock starts and stops

The clock starts when the surface is wetted with solution, not when you open the packet or finish activating it. The clock effectively stops if the surface dries before the 10 minutes are up, because a dry surface is no longer in contact with the disinfectant. That is why the label calls for the solution to be applied to ensure visible wetness of the surface being treated: visible wetness, held for the full time, is the standard.

How to hit 10 minutes on a real grow-room surface

This is the gap the product pages leave: they quote the sentence but do not tell you how to keep a bench wet for 10 minutes.

The re-wet rule

In a warm, dry room, a sprayed film can flash off before 10 minutes. The fix is simple and label-consistent: if the surface looks like it is drying before the 10-minute mark, re-wet it so it stays visibly wet for the full exposure time. You are not changing the dose; you are maintaining the wet contact the label requires. Smooth surfaces like stainless benches and totes hold wetness longer; porous surfaces like painted concrete and drywall dry faster and usually need a re-wet pass.

Surface by surface

Stainless benches, trays, and totes are the easy case: a single even application often holds visible wetness long enough, with a possible top-up. Porous concrete floors and drywall drink the solution and dry fast, so plan on at least one re-wet to carry the full 10 minutes. Hanging equipment (light reflectors, ducting, trellis netting) and fabric-pot rims are awkward to keep wet and usually need more than one pass. Pre-clean visibly soiled surfaces first with a non-disinfectant cleaner, because a heavy soil load consumes the ClO2 and shortens the effective dwell.

Confirming 100 ppm at the point of use

Time is half the label condition; concentration is the other half.

Mix to the label and verify

ProKure V is activated by adding the pouch to water in an opaque (not clear) container and agitating per the label until full activation, which the label notes takes about one hour to reach full strength, with the pouch and water sized to the target 100 ppm. Chlorine dioxide test strips are the practical way to confirm you are at roughly 100 ppm at point of use rather than assuming.

The 15-day window and the opaque container

Activated solution is meant to be used within 15 days of activation and stored in a dark, closed container away from sunlight, because ClO2 concentration drifts down over time and light accelerates the loss. A solution mixed at 100 ppm on day one is not necessarily at 100 ppm two weeks later, so verify before relying on the dwell. The opaque container is part of holding the concentration, not an optional preference.

The compliance log an auditor wants

A disinfection pass you cannot prove is one an auditor cannot credit.

What to record per pass

Log the date, the room, the surfaces treated, the confirmed ppm, the dwell start and stop times, the technician, and any corrective action (such as a re-wet). Those fields turn "we disinfect" into a defensible record, and for a procurement or QA lead chasing documentation at audit time, the dwell log is exactly the proof that is usually missing. For a multi-state operator, the same log template standardizes the record across every facility and state.

Deviations are off-label

Spell out the failure modes so the crew understands the stakes: a 5-minute dwell instead of 10 does not meet the kill claim and leaves organisms alive; 50 ppm instead of 100 does not meet the claim either; and running far above 100 ppm wastes product and risks corrosion on some surfaces. All three are inconsistent with the labeling. Hit 100 ppm for 10 minutes, no more and no less, and the pass is both effective and compliant.

Does 10 minutes at 100 ppm cover your pathogen, and where V fits

Tie the dwell back to the problem and to the rest of the system.

The label kill list

Used at 10 minutes at 100 ppm on hard non-porous surfaces, ProKure V's label fungicide claims include Aspergillus niger (ATCC 9642), Fusarium solani (ATCC 36031), Penicillium digitatum (ATCC 201167), and Botrytis Sp, alongside bacteria such as MRSA (ATCC 33591). So the standard surface dwell covers the molds a cultivation facility worries about most, on surfaces, when you actually hold the time and concentration.

Where ProKure V sits in the system

ProKure V is the surface half of the system: the EPA-registered liquid for hard surfaces, suitable for use with plants in the room for surfaces, leaving no residue. The air half is separate: ProKure D is the slow-release gas that runs in the room with plants in for ongoing air quality (not an EPA-registered product, per its 40 CFR disclaimer), and ProKure G is the fast-release gas for an empty-room reset (not for use with or on plants, crops, or feed). If your problem is whole-room air rather than a surface, V's 10-minute dwell is not the tool; the gases are. Educate here on groclarity.com, buy ProKure V on shop.groclarity.com, and pull the label and SDS from prokuresolutions.com.

Related resources