ProKure G Work Cycle: What Happens During the 4 to 6 Hours (and How to Plan Around It)
ProKure G needs at least 4 to 6 hours of treatment time in an unoccupied room, then a 1-hour ventilation window before re-entry, so budget 5 to 7 hours of total room downtime per treatment. During that window the water-activated pouch releases chlorine dioxide gas that fills the room and works on odor-causing bacteria, mold, and mildew. It is a between-harvest, empty-room product, labeled not for use with or on plants, crops, or feed, so the room is cleared of crop, people, and pets while it runs. Below: what happens inside the window, why it is sometimes 4 hours and sometimes 6, and how to schedule a shift or turnover around it.
The work cycle, start to finish
The label instruction is short: as ProKure states it, "Allow at least 4-6 hours for the system to work." That is the treatment window, not the whole downtime. Add the ventilation step: after the dwell, you ventilate and turn the lights on for one hour before re-entry. So the real room-out number is the 4 to 6 hour treatment plus the 1 hour ventilation, which is why 5 to 7 hours is the figure to put on the schedule. If odors remain after a cycle, the label says to repeat the treatment, which means a second full window, so a heavily loaded room can take a longer block than a single pass.
Two housekeeping facts that affect the clock. The pouch is activated with water and starts releasing gas on contact, so the window begins when you place it, not when you leave. And ProKure G carries a CAUTION signal word and is a deodorizing product; it controls odor-causing bacteria, mold, and mildew in an empty room, and it is not a product you run around a live crop.
What is happening during the 4 to 6 hours
Chlorine dioxide is a true gas once activated, not a liquid or a mist, which is what the time window is for. Over those hours the gas builds to a working concentration and distributes through the room volume, reaching into cracks, crevices, and the corners a wipe-down misses. That even, gas-phase fill is the whole reason the product works on the air and surfaces of a space rather than only where a sprayer reached. The 4 to 6 hour range is the time it takes for that saturation and contact to do its deodorizing job across a room, not a single surface.
The room is dark on purpose. Per the product guidance, ProKure G "Works best in the dark," so the lights go off for the treatment and come back on for the ventilation hour. An air mover inside the room helps distribute the gas during the window. None of this is visible, which is why growers want the expectation set: the room looks like nothing is happening while the gas is doing the work.
Why it is 4 hours on one job and 6 on another
The range is not arbitrary; four things move it. Room volume is the first: a larger space takes longer for the gas to reach a working concentration throughout, so size the pouch to the room (a 10-gram pouch covers approximately 1,000 cubic feet, a 25-gram approximately 2,250 cubic feet) and give a bigger room the longer end of the window. Seal quality is the second: a tight room holds the gas and works faster, while a leaky room with gaps at the door sweeps or an active air exchange loses gas and needs the full 6 hours, with ventilation set to recirculation or off during treatment.
Temperature and odor severity round it out. Cooler rooms and heavier odor or microbial loads push toward the 6-hour end, lighter everyday jobs toward 4. When in doubt, run the longer window; the cost of an extra two hours of downtime is smaller than a re-treat. For the pouch-size decision, the coverage guide covers 10g versus 25g, and for the physical activation steps, the activation guide walks the pouch, cup, and water.
Planning a shift or turnover around the window
Treat the 5 to 7 hour total as a scheduling block, not a background task. The cleanest pattern is an overnight run: activate at end of shift, let the 4 to 6 hour window run while the room is empty, and ventilate for the final hour so the room is ready at the start of the next shift. For a daytime turnover, start the cycle early enough that the treatment and the ventilation hour both finish before you need the room back. If you are running a full between-harvest reset, the ProKure G window comes after the deep clean and surface disinfection, so sequence it as the air step at the end, not the first move.
Use the enclosed caution placard to record the treatment start time and the earliest safe re-entry time on the door, so the whole crew reads the same number and nobody walks in early. That placard is also your sanitation record for the room. Because the room must be empty of crop, people, and pets for the whole window, a multi-room facility runs G on a room that is already between cycles, not on an occupied flower room.
Re-entry and what ProKure G is not for
When the dwell ends, ventilate and turn the lights on for one hour before re-entry. Do not re-enter a treated room before that ventilation hour: chlorine dioxide gas is an irritant to the respiratory tract, which is the reason the room is cleared and vented. For the full PPE and re-entry detail, the re-entry and ventilation guide covers it.
The label line that governs the whole product: ProKure G is EPA Reg. No. 87508-2-89334 and is labeled not for use with or on plants, crops, or feed. That makes it a between-harvest, empty-room tool. If you need a product that runs with plants in the room, ProKure G is the wrong one: the slow-release ProKure D is an air-quality gas that runs with plants, and ProKure V is a liquid disinfectant for hard surfaces that is suitable for use with plants in the room. The deep labels and SDS live on prokuresolutions.com.
Frequently asked questions
How long does ProKure G take to work?
At least 4 to 6 hours of treatment time in an unoccupied room, then a 1-hour ventilation window before re-entry, so plan on 5 to 7 hours of total downtime. Larger rooms, leaky rooms, cooler temperatures, and heavier odor loads push toward the 6-hour end. If odors remain after a cycle, the label says to repeat the treatment.
Why does ProKure G need 4 to 6 hours and not less?
Chlorine dioxide is a gas, and the window is the time it takes to build to a working concentration and distribute through the whole room volume, reaching cracks and corners a wipe-down misses. Cutting the window short means the gas has not saturated the space, so the treatment underdelivers and you end up re-treating anyway.
Can I be in the room during the ProKure G work cycle?
No. People and pets must be out for the entire 4 to 6 hour window, and so must any crop, because ProKure G is labeled not for use with or on plants, crops, or feed. You re-enter only after the treatment plus the 1-hour ventilation step. Post the caution placard with the start and safe re-entry times so the crew stays out.
Does the room need to be dark for ProKure G to work?
Yes, it works best in the dark, so turn the lights off for the treatment window and bring them back on for the ventilation hour. An air mover running inside the room during the window helps distribute the gas evenly, which matters most in larger or less-sealed rooms.
How do I schedule a grow room around the ProKure G work cycle?
Treat the 5 to 7 hour total as a block. The simplest pattern is overnight: activate at the end of a shift, let the 4 to 6 hour window run in the empty room, and ventilate for the last hour so the room is ready for the next shift. In a between-harvest reset, run the G window as the final air step after the deep clean and surface disinfection.
Related resources


