ProKure G resets an empty grow room between cycles in a single shift. The whole workflow is: clear the room, do a ProKure V surface pass, size the gas to the room volume, seal and activate, hold the 4 to 6 hour dwell with no one inside, then ventilate and turn the lights on for one hour before re-entry. The one rule that governs all of it is the label: ProKure G is a fast-release chlorine dioxide gas for unoccupied spaces, and it carries the verbatim restriction "Not for use with/on plants/crops/feed." If plants are hanging, this is the wrong page and the wrong moment. Everything below assumes an empty room.
Before you start: is ProKure G the right product for this room?
ProKure G is the between-cycle, empty-room tool. It is a water-activated, fast-release ClO2 gas (EPA Reg. No. 87508-2-89334) that controls odor-causing bacteria, mold, and mildew as a deep-penetrating vapor, and because it is a true gas it reaches the screens, drain lines, and plenum voids a sprayer never touches. That reach is only legal and safe when the room is empty.
What empty means
Empty is literal. The crop is out, every piece of plant material and trim is removed, feed is out, and cultivation media is handled per its own SDS. People and pets are out for the entire treatment. If any living plant is in the room, ProKure G is off the table because the label says "Not for use with/on plants/crops/feed." For a live canopy you want a different product entirely: ProKure D, the slow-release gas that provides ClO2 protection for up to 30 days and improves air quality with plants present, or ProKure V for a surface pass on an empty bench while plants live elsewhere.
Why gas belongs in turnover
The empty window is exactly when a whole-room gas earns its place. There is nothing a liquid spray reaches that the gas does not, and the gas gets into the cracks and return manifolds where mold hides between cycles. Read the plant restriction as a scheduling rule, not a limitation: you run G when the room is empty, which is when you most need total coverage.
What you need before step one
Stage everything so activation is not interrupted mid-procedure. You need the ProKure G packets sized to the room (see the sizing section), the reusable dispersion cup, water, a timer, PPE per the label, sealing materials (poly sheeting and tape for leaks, a plan for HVAC isolation), re-entry signage, and your verification tools. Keep the Safety Data Sheet and the product label on hand; both live on prokuresolutions.com for your audit binder.
Sizing: how many packets your room needs
Size the gas to the air volume, not the floor. ProKure G covers approximately 1,000 cubic feet per 10 gram packet and approximately 2,250 cubic feet per 25 gram packet. Measure length times width times height to the ceiling, because the gas fills the whole volume. A 12 by 12 by 10 clone or mother room is 1,440 cubic feet, so one 25 gram packet covers it. A 20 by 40 by 10 flower room is 8,000 cubic feet, which takes four 25 gram packets (9,000 cubic feet of coverage) placed equally apart. A 30 by 60 by 12 large flower room is 21,600 cubic feet, which takes ten 25 gram packets distributed across the floor for even fill. When a room lands between counts, round up, because under-dosing the air volume is the quiet way a turnover clean fails.
The 4-6 hour empty room cycle, step by step
The activation mirrors the approved ProKure G label, and the whole turnover blocks out to a single shift.
Step 1, prep (0:00 to 0:30)
Remove the finished crop and every piece of plant material, including fallen trim and larf. Confirm the room is empty of plants, feed, and people. This is the first compliance checkpoint, not a formality. Then dry-vacuum debris off screens, racks, hang lines, and the floor, because organic soil is oxidizer demand that spends the gas before it reaches your target.
Step 2, surface pass and seal (0:30 to 1:00)
Wipe down the hard, non-porous surfaces (benches, trays, tool racks, drain pans) with ProKure V, the liquid sibling, held at a 10-minute contact time at 100 ppm. V is residue-free and suitable for use with plants in the room, so it is safe to run during prep. Then seal the room: turn HVAC off with dampers closed, or set it to recirculate if the system serves only this room, and poly-and-tape any obvious leaks.
Step 3, activate (1:00 to 1:15)
Tear open the foil package, remove the white inner pouch, and do not open the white inner pouch. Place the end of the pouch that has the square indentations into a plastic cup filled with 1.5 inches of water. Set the cup on a stable, level surface in a central location, holes facing up, and for larger rooms place multiple packets equally apart for even coverage.
Step 4, dwell (1:15 to at least 5:15)
Turn off the lights (ClO2 works best in the dark), use an air mover if you have one to help distribute the gas, and exit. Allow at least 4 to 6 hours for the system to work, or overnight. Nobody enters during the dwell. Do not crack the door mid-dwell: opening the room vents the gas and resets the clock.
Step 5, ventilate (after the dwell)
Ventilate and turn the lights on for one full hour before re-entry. This ventilation step is a label condition of use, not a suggestion. Route exhaust safely and let the room clear.
Step 6, verify
Start with the obvious (visible mold gone, musty odor eliminated), then add a measurement: an ATP swab on surfaces and a pre-cycle yeast and mold plate give you a number, and tracking that number across cycles builds the trend data an auditor and an owner both want. If odors reappear, the label allows repeating the treatment.
Step 7, document and re-enter
Log the date, room, packet count and lot, dwell duration, ventilation time, re-entry time, and operator initials, transcribed from the caution placard you post on the door. Then re-enter and stage the next cycle.
EPA label compliance for cannabis facilities
EPA compliance sits at the top of a cultivation lead's worry list, so the procedure carries it in-line rather than in a footer. ProKure G is EPA-registered, and it is a violation of Federal Law to use an EPA-registered product in a manner inconsistent with its labeling. The empty-room requirement, the 4 to 6 hour dwell, and the one-hour ventilation are conditions of use. The restriction "Not for use with/on plants/crops/feed" is the line that defines when G may run at all. File the EPA registration number, 87508-2-89334, with the SDS and the master label from prokuresolutions.com so an inspector sees them in one place.
How this cycle cuts turnover from days to hours
A bleach or quat turnover can cost three to five days of downtime: fumes force an evacuation, surfaces need a long air-out, and quat residue lingers. The ProKure G cycle runs in a single shift, and the gas controls mold and odor without leaving a residue film. Collapsing a multi-day reset into 4 to 6 hours is not just convenience, it is extra cycles per year, which is the owner-facing ROI hiding inside a procedure page.
When a competing gas chemistry is the wrong fit
Gas enclosure treatment is an established agricultural concept, but not every gas chemistry fits an occupied-adjacent cultivation workflow. A poultry-industry patent on dry hydrogen peroxide gas is blunt about its own chemistry's ceiling, noting that vaporized peroxide at working droplet concentrations reaches a level that "is toxic and cannot be used in occupied areas," and that "vaporized peroxide is highly corrosive and can damage incubators and other equipment in the area even after a single use." ProKure G is also an empty-room product, but the workflow is built around a defined dwell and a one-hour ventilation-then-verify step so the room returns to safe re-entry on a clock, with no lingering corrosive residue on your equipment. Match the chemistry to a workflow you can actually run between cycles.
Troubleshooting
If the room is larger than your packet count covers, add packets and distribute them evenly rather than clustering one in a corner. If activation seems slow, confirm the pouch indentations are sitting in the water and the room is dark. If you smell chlorine after re-entry, your ventilation hour was not enough: ventilate longer and re-check before the crew returns. If an ATP swab or spore count is still elevated, repeat the treatment (the label allows it) and re-check your prep step, since leftover organic debris is the most common cause of a gas that underperforms. If an adjacent room has live plants, confirm HVAC isolation and sealing before you treat, because the restriction protects those plants too.
Related resources


