ProKure G Between-Harvest Deep Clean: The Full Room-Turnover Gas Protocol

A ProKure G deep clean between harvests is an empty-room gas treatment that resets your grow room's air after a crop comes down and before the next one goes in. ProKure G is an EPA-registered fast-release ClO2 gas (EPA Reg. No. 87508-2-89334) that controls mold and mildew, odor-causing bacteria, and chemical odors. Its label carries one non-negotiable line: Not for use with/on plants/crops/feed. So the room has to be empty. You prime a packet with water, let the gas dwell 4 to 6 hours, ventilate for one hour, then re-enter. One 25g packet treats roughly 2,250 cubic feet.

This page is for the cultivator who has already chosen G and wants to know what the treatment looks like from packet-open to re-entry. If you have not decided which ProKure product fits your between-cycle job, start with the three-way comparison of ProKure V, G, and D first, because V and G do different jobs and you do not want to run the wrong one in an occupied room.

What "deep clean between harvests" actually means with ProKure G

The between-harvest window is the gap between striking a finished room and restocking it with clones or vegging plants. In a four-light flower room that gap is usually 24 to 72 hours: pull the plants, strip the trellis, wipe surfaces, reset the canopy, and bring the air back to a clean baseline. ProKure G owns the air half of that reset.

Here is what a gas treatment does that a wipedown cannot. A rag reaches flat, visible surfaces. ClO2 gas is a true gas, so it fills the whole volume evenly and reaches the cracks, the gaps behind equipment, and the microscopic pores in concrete and drywall where spores sit. The incumbent reseller pages lean hard on that chemistry point. Hydrobuilder's own copy says ClO2 "can penetrate into very small areas," and that is precisely the gap a between-harvest wipedown leaves open.

The EPA-registered claim, in plain language: ProKure G is registered as a deodorizing gas that controls mold and mildew, odor-causing bacteria, and chemical odors. It is not a plant treatment. The registration and the plant/crop/feed restriction are two sides of the same fact. G works in the room, not on the crop. That is why every reputable description of G carries the restriction, and it is why GroClarity puts it in the first screen of this page instead of burying it in a footer.

Before you activate: room-prep checklist

Plants come out. That is the first and hardest rule, and it is a label restriction, not a preference. Not for use with/on plants/crops/feed. If a clone or a mother is in the room, you are using the product in a manner inconsistent with its labeling, which is a violation of federal law. Pull every living plant, plus any feed sacks or nutrient totes sitting open.

Then shield what the gas can mark. ProKure's label says keep G 18 to 24 inches away from fabrics, leather, electronics, mirrors, metals, and plated surfaces. Hydrobuilder frames the same guidance as "Place two feet from fabrics, leathers, electronics, mirrors and uncoated metals." Move those out or set the packet so nothing sensitive sits inside that two-foot radius. ClO2 is a strong oxidizer. It will dull an unprotected uncoated-metal surface over a long dwell.

Set the environment. Lights off; ProKure G works best in the dark. If a ventilation system serves only this room, set it to recirculate so the gas distributes instead of exhausting. If the system is shared, turn it off and close the ducts. An air mover on low helps the gas reach corners. Check temperature and humidity before you start; a room that is very cold or sitting above roughly 80 percent humidity changes how the packet behaves, which the troubleshooting section covers.

Choose the right SKU. The two sizes are the 10g packet, rated for 1,000 cubic feet, and the 25g packet, rated for 2,250 cubic feet. Do the room math instead of guessing. A 12 by 12 by 10 flower room is 1,440 cubic feet, which is past what a single 10g packet covers, so you want one 25g packet. A double-row 20 by 30 by 12 room is 7,200 cubic feet and needs four 25g packets placed equally apart. Under-dosing a room is the most common reason a treatment underperforms, and none of the reseller PDPs walk the coverage math out for real room sizes.

Step-by-step activation

These four steps are the ProKure G activation sequence. Follow the label; the notes after each step are cultivator context, not a substitute for the label.

Step 1. Tear open the foil package and remove the white inner pouch. Do not open the white inner pouch. The dry ingredients stay sealed; you are activating through the pouch wall, not pouring anything out.

Step 2. Place the end of the white pouch that has the square indentations into a plastic cup filled with 1.5 inches of water. Room-temperature water is fine. That cup is reusable for future ProKure G treatments, so keep it with your turnover kit.

Step 3. Place the cup on a stable, level surface in a central location, holes facing up. Turn off the lights. If applicable, turn on air conditioning or ventilation to circulate the air. For a large room, stage multiple packets equally apart rather than clustering them in one corner.

Step 4. Allow at least 4 to 6 hours for the system to work. Ventilate and turn on the lights for one hour before re-entry. Repeat the treatment if odors reappear. Use the enclosed caution placard to record the treatment start and the safe re-entry time; that timestamp is the first line of your audit trail.

What the room will look like during the treatment

Cultivators who have never run a gas treatment want to know what they will see and smell, and no competitor page says. During the dwell you may notice a faint yellow-green tint to the air in the room; that is the ClO2 gas doing its job. There is a chlorine-like odor, strongest when you open the door to ventilate. It is sharp but it clears fast once air moves. If you run an air-quality or ClO2 meter, you will see the reading climb during the dwell and fall through the ventilate hour. People and pets stay out for the whole dwell plus the ventilate hour. Do not inhale the gas.

Repeat the treatment when odors return or when you are resetting a room that carried a heavy spore load the prior cycle. For a room coming out of a confirmed mold event, a second pass after the first ventilate is reasonable judgment, not a fixed schedule. The label sets no alternation or rotation cadence for G, so do not invent one; treat, verify, and repeat only if the odor or your post-treatment air test says to.

Where ProKure G fits in the full room-turnover sequence

ProKure runs as a three-product system, and G is the air step. V is the liquid you use on surfaces you can wipe: it is a hospital-type disinfectant, it leaves no residue, and it is suitable for use with plants in the room, which is exactly the opposite of G. If your between-cycle job is surface turnover with plants nearby, that is a ProKure V job, and residue-sensitive readers should price V instead of G. G is the empty-room air-and-cracks step that follows your surface work. D is the slow-release gas that provides ClO2 protection for up to 30 days of ongoing air-quality maintenance once the room is replanted.

The practical order in a turnover: strike the room, wipe hard surfaces with V, run the G gas deep clean while the room is empty, then set D for extended-release maintenance once plants go back in. For the full multi-product sequence with order-of-operations across all three, GroClarity publishes a dedicated between-harvest room-turnover protocol; this page stays focused on the G gas step so the procedure is not buried inside a longer workflow.

Building your audit trail: EPA and state compliance documentation

Steven, the head grower, and the procurement lead both need to prove the treatment happened, because a pre-sale mold test and a state inspection both ask for records. ProKure gives you the hooks; GroClarity turns them into a file.

Start with the caution placard. It records treatment start and safe re-entry time. Photograph it and date it. File the ProKure G SDS and label alongside it; both live on prokuresolutions.com, which is where you pull the EPA registration number and the directions for state inspection. Then correlate air-test data. If you run a yeast and mold load test before and after the turnover, the delta is the evidence that the sanitation protocol works, and it is the number ownership and a compliance auditor actually want to see.

State compliance has variance worth flagging for multi-state operators. ProKure G carries a California shipping restriction at the reseller level, and cannabis-use language varies state to state even on an EPA-registered product. A cultivation director coordinating protocols across several states should standardize the documentation, not just the product, so every facility files the same placard, SDS, and air-test record. GroClarity helps multi-state operators centralize that.

Cost per treatment and reorder cadence

The honest cost comparison is per cubic foot, not per packet. By reseller pricing, a 10g packet runs about $26.60 and covers 1,000 cubic feet, which is $26.60 per 1,000 cubic feet. A 25g packet runs roughly $40 and covers 2,250 cubic feet, which works out to about $17.77 per 1,000 cubic feet. The larger packet is cheaper per cubic foot, so for rooms over 1,000 cubic feet the 25g is the better buy. No competitor PDP states this, even though it is the number a procurement lead needs.

Run the reorder math off your room count and harvest cadence. A four-room facility turning rooms monthly burns packets faster than a two-room operation, and a 10-room facility is ordering by the case. Weigh that against the prevention math an owner cares about: one failed mold test on a mature crop runs into six figures, and a between-harvest G treatment costs under $40 per 2,250 cubic feet. Prevention is the cheaper line item by orders of magnitude.

Troubleshooting

Packet not fizzing. Check that the square-indentation end is actually in the water and that the cup holds a full 1.5 inches. A packet past its shelf life or one that never contacted water will not generate. Reseat it and give it time; the generation is not instant.

Room too cold or too humid. ClO2 is more soluble in cold water, but very cold room air slows the generation kinetics, so a chilly room may need a longer dwell toward the 6-hour end. Humidity above roughly 80 percent can interfere with even distribution; dehumidify toward your normal grow-room range before treating.

Persistent odor after treatment. If the smell returns after a full ventilate, repeat the treatment per the label. A lingering odor usually means the room carried more load than one packet-per-rated-volume could clear, which points back to the coverage math: verify you dosed for the real cubic footage, not an estimate.

Related resources