ProKure G Deep-Clean Between Harvests: The Turnover Protocol for Cannabis Cultivation Facilities
The between-harvests window is the highest-leverage clean of the whole cycle, because the room is empty and you can reach every surface and void before the next crop locks the space down for weeks. ProKure G is the gas built for that window: an EPA-registered fast-release chlorine dioxide vapor (EPA Reg. No. 87508-2-89334) that controls odor-causing bacteria, mold, and mildew. It runs in an empty room only, because the label reads not for use with/on plants/crops/feed, and that restriction is why it belongs in turnover rather than a live cycle. For the product overview and chemistry, see the ProKure G fast-release gas pillar. This page is the protocol: strip, surface-prep, gas, dwell, ventilate, verify, document.
What "between harvests" actually means, and why G belongs there
Between harvests is a specific state, not a loose window. It means the crop is out, the room is stripped of plant material, and the space is empty of people and plants for the duration of the treatment. That is the only state ProKure G is labeled for.
The plants restriction is the whole reason the timing matters. ProKure G carries the verbatim line not for use with/on plants/crops/feed, so you cannot run it around a living canopy. Read as a scheduling rule rather than a limitation, that is a feature: the empty turnover window is exactly when you want a whole-room gas that reaches the cracks, drain lines, and plenum spaces a sprayer never touches. If you need air-quality control with plants in the room, that is a different product, the slow-release ProKure D, which provides improves-air-quality coverage for up to 30 days and runs with the crop present.
Before you gas: strip and surface-prep
Gas treats the air and the voids, but it is not a substitute for clearing the room first, and a rushed prep is where a turnover clean underperforms.
Strip and haul first. Remove the finished crop and every piece of plant material, including fallen trim and debris, because organic soil is oxidizer demand that spends the gas before it reaches your target. Then do a surface wipedown on the hard, non-porous surfaces, benches, trays, tool racks, drain pans, with the liquid sibling, ProKure V, which is residue-free and usable with plants in the room if any remain nearby during prep. V knocks the surface load down so G can handle the air. Last, plan the seal and the ventilation: cover the room's openings, decide whether the HVAC recirculates or shuts with ducts closed, and stage your materials (packets, the reusable dispersion cup, water, a timer, re-entry signage, and PPE per the label) so activation is not interrupted.
Sizing: how many packets your room needs
Every competitor page stops at the raw coverage number and leaves the arithmetic to you. One retailer's copy is typical, selling the product on being EPA-registered and residue-free "without generating any hazardous residues" while never translating coverage into a real room. Do the math instead.
ProKure G covers approximately 1,000 cubic feet per 10 gram packet and approximately 2,250 cubic feet per 25 gram packet. Measure length times width times height to the ceiling, because the gas fills the whole volume. A 12 by 12 by 10 clone or mother room is 1,440 cubic feet, so one 25 gram packet covers it. A 20 by 40 by 10 flower room is 8,000 cubic feet, which needs four 25 gram packets (9,000 cubic feet of coverage) placed equally apart. A 30 by 60 by 12 large flower room is 21,600 cubic feet, which needs ten 25 gram packets distributed across the floor for even fill. When a room lands between counts, round up, because under-dosing the air volume is the quiet way a turnover clean fails.
The step-by-step activation and dwell
The activation mirrors the approved ProKure label exactly, and the whole turnover blocks out to a single shift. Tear open the foil package, remove the white inner pouch, and do not open the white inner pouch. Place the end of the pouch that has the square indentations into a plastic cup filled with 1.5 inches of water; the cup is reusable for future treatments. Set the cup on a stable, level surface in a central location, turn off the lights (ClO2 works best in the dark), and if applicable turn on air conditioning or ventilation to circulate the air. Allow at least 4 to 6 hours for the system to work. Then ventilate and turn on the lights for one hour before re-entry, and repeat the treatment if odors reappear.
As a turnover timeline that reads: hour 0 to 2, strip, haul, and the ProKure V surface wipedown. Hour 2 to 3, seal the room, activate the G packets, and exit. Hour 3 to 9, the sealed gas dwell, 4 to 6 hours minimum, with no one entering. Hour 9 to 10, ventilate and restore the lights. Hour 10 and after, re-enter, verify, and stage the next cycle. Do not crack the door mid-dwell: opening the room vents the gas and resets the clock.
How you know it worked, and when the protocol changes
Running the gas is half the job; confirming it worked is the half that makes the turnover defensible. Start with the obvious, visible mold gone and the musty odor eliminated, then add a measurement: an ATP swab on the surfaces and a pre-cycle yeast and mold plate baseline give you a number, and tracking that number across cycles builds the trend data an auditor and an owner both want.
The protocol has edges. If you just failed a pre-sale yeast and mold panel on a harvested batch, the same empty-room turnover clean applies before the next crop, and the label allows repeating the treatment if odors reappear. But if you find visible mold mid-cycle with plants in the room, G is the wrong tool, because it is not for use around plants: that is a surface-disinfection conversation for ProKure V and an air-quality conversation for ProKure D, not a reason to gas a live canopy. And for growers weighing the switch from bleach or quats, the case is the crew: bleach fumes force an evacuation and a long air-out, and quat residue lingers on surfaces, where the ProKure G gas controls mold and odor without a residue film.
EPA compliance and the documentation your auditor wants
EPA compliance is the worry at the top of a cultivation lead's list, so the protocol closes with the paper trail rather than burying it. ProKure G is EPA-registered, and the governing rule is verbatim: it is a violation of Federal Law to use EPA-registered products in a manner inconsistent with the product labeling. The empty-room requirement, the 4 to 6 hour dwell, and the one-hour ventilation are conditions of use, not suggestions.
File the registration number, EPA Reg. No. 87508-2-89334, with the Safety Data Sheet and the master label, all available from prokuresolutions.com, so an inspector sees them in one place. Keep a per-turnover treatment log: date, room, packet count and lot, dwell duration, ventilation time, re-entry time, and operator initials, transcribed from the caution placard you post on the door. For a multi-state operator, write that log and the timeline into the corporate SOP so every facility runs the identical turnover and keeps the identical record; confirm any state-specific label supplement with the state regulator. To reorder packets, that is shop.groclarity.com, and to standardize the turnover across a footprint or size packets to your actual rooms, request a quote from GroClarity.
Related resources


