ProKure G Between Harvests: The 4-6 Hour Fast Air Reset

ProKure G is a fast-release chlorine dioxide gas, EPA Reg. No. 87508-2-89334, that resets the air in a stripped, unoccupied grow room between harvests. You slide the water-soluble pouch into a dispersion cup filled with 1.5 inches of water, place it on a level surface in a central spot, turn off the lights, and allow at least 4 to 6 hours for the system to work. Then you ventilate and turn on the lights for one hour before re-entry. No people and no plants are in the room during treatment. That is the whole window, and it is schedulable.

Search this product and you get the same sentence on six different store pages: formulated for use between harvests to control odor-causing bacteria, mold and mildew, ProKure G is an EPA-registered ClO2 technology. The manufacturer page gives you Step 1 through Step 4. What none of them tell you is where those four steps sit inside a real turnover, what the room has to look like before you activate, and how you file the reset so it survives an audit. A head grower planning a turnover is not asking what ProKure G is. The question is whether a fast air reset fits a window the crew can schedule against, and what proof exists that it worked. Below is the operational version.

What "between harvests" actually means for a fast air reset

A turnover is not one task. Crews run it in phases: strip the spent plants, haul out media and debris, wipe down heavily soiled surfaces, disinfect hard surfaces, run the gas reset, bring environmental controls back up, then replant. The ProKure product page lists activation Step 1 through Step 4 with no reference to any of that. One of the ranking retailer pages opens with the line that ProKure G attacks "odor causing bacteria, mold, mildew and chemical odors (including harmful VOC's) without generating any hazardous residues," which is accurate for the product but tells a facility manager nothing about when in the turnover to run it.

The gas reset sits late in the sequence. Run it after you have removed the obvious soil and after any surface disinfection, because ProKure G works on the air and the hard-to-reach volume of the space, not as a substitute for cleaning visible grime off benches and walls. ProKure G is a deodorizing fast-release gas that controls odor-causing bacteria, mold and mildew in the treatment space. It is not a surface disinfectant and it carries no kill claims. If you need bench tops, walls, and tools disinfected, that is a different job and a different product. See our guide to surface disinfection between cycles with the liquid ClO2 line for that half of the turnover.

The reset goes before you bring environmental controls and new clones back in, because the room has to stay unoccupied for the full treatment plus the one-hour ventilation. Slot it so the 4-to-6-hour window plus the vent hour lands inside your scheduled downtime, overnight if that is cleaner, and the room is ready for replanting the next morning.

Where the gas reset sits, and what it does not replace

Think of the reset as the air half of a two-part turnover. A fast air reset handles the air and the full volume of the room, including the corners and gaps a spray bottle never reaches. It does not scrub a soiled bench or disinfect your trim tools. When the turnover calls for hard-surface disinfection, the liquid ClO2 line is the tool: a hospital-type disinfectant you can use with plants in the room, applied to surfaces at label concentration, residue-free. Pair the two and the turnover is covered end to end, air and surfaces, which is what a clean next-cycle start actually requires. If chlorine dioxide itself is still new to you, start with our explainer on what chlorine dioxide is and how it is activated before you build the protocol, then come back and schedule the reset. The point is sequence: clean the visible soil, disinfect the surfaces, then reset the air, and do it in that order so each step is not undone by the one before it.

The 4-6 hour treatment window, step by step

The activation itself is short. The waiting is the window.

Step 1: prep the room

The space must be unoccupied: no people, no plants, no feed. Remove the odor source and clean heavily soiled surfaces first. Turn off the lights. If a ventilation system serves only this room, set it to recirculate so the gas distributes; otherwise turn the system off and close the ducts. An air mover in the room helps spread the vapor evenly. Cover smoke detectors, and keep the pouch no closer than 18 to 24 inches from fabrics, leather, electronics, mirrors, and metal surfaces, per the label placement guidance.

Step 2: activate the pouch

Tear open the foil packet and remove the white inner pouch. Do not open the white inner pouch. Place the end of the pouch that has the square indentations into a plastic dispersion cup filled with 1.5 inches of water, then set the cup on a stable, level surface in a central location with the holes facing up. The dispersion cup is reusable for future treatments. For the full torn-pouch and water-cup walkthrough, see our ProKure G activation instructions with the water-cup method; this page summarizes it rather than repeating every detail.

Step 3: let it work

Allow at least 4 to 6 hours for the system to work, or run it overnight. Do not re-enter during this window. This is where the "fast release" name earns itself: a full room reset inside a single turnover window, not a multi-day hold. The gas disperses, does its work on odor-causing bacteria, mold, and mildew in the air, then begins to dissipate.

Step 4: ventilate and re-enter

Ventilate and turn on the lights for one hour before re-entry. Repeat the treatment if odors reappear. That one-hour vent is not optional padding; it is the re-entry gate on the label, and it is the line between a compliant reset and a violation.

Sizing the reset to your room

Coverage runs by pouch size. A 10 gram pouch covers approximately 1,000 cubic feet. A 25 gram pouch covers approximately 2,250 cubic feet. Those are the two sizes, and they are the numbers the retailer pages quote verbatim because they come straight off the label.

The math is where growers get caught. A 12 by 12 by 8 foot flower room is 1,152 cubic feet. That is already over the 1,000-cubic-foot coverage of a 10 gram pouch, so the 25 gram pouch, at 2,250 cubic feet, is the right call with headroom to spare. Undersizing is the quiet failure mode: the gas disperses but never reaches an effective concentration across the full volume, and you conclude the product underperformed when the real problem was coverage. When a room runs larger than a single pouch covers, use multiple pouches placed equally apart for even distribution rather than one pouch working too hard in a corner. To run your exact room volume against pouch coverage, use our ProKure G coverage calculator for the 25g and 10g sizes. Measure the room in cubic feet first, length times width times height, then match the pouch, and always round up rather than down.

What "unoccupied" actually means (and how to comply)

The compliance worry is real and the ranking pages barely touch it. The manufacturer FAQ states ProKure G fast gas "is for unoccupied spaces, no people or plants in the space during treatment time," and then stops. A facility manager needs more than one sentence.

Unoccupied means no people, no plants, and no feed inside the treatment space for the entire 4-to-6-hour window and the one-hour ventilation that follows. It also means the gas stays where you put it. If a shared HVAC system connects the treatment room to adjacent occupied rooms, isolate it: set a dedicated system to recirculate, or shut the shared system off and close the ducts, so chlorine dioxide gas does not migrate to a space where crew are working. Seal obvious door gaps, post signage with the treatment start time and the safe re-entry time, and control the keys so nobody walks in mid-cycle. Chlorine dioxide gas is irritating to the respiratory tract at concentration, which is the entire reason the room stays empty.

The label language is not advisory, and it belongs on your page and in your SOP binder verbatim:

Not for use with/on plants/crops/feed. Always read product labels before use.

This material is not a replacement for the product label. It is a violation of Federal Law to use EPA registered products in a manner inconsistent with the product labeling.

That verbatim block is the difference between an education page a grower trusts and a retailer page that hopes nobody asks. GroClarity treats EPA compliance as part of how the page is written, not a disclaimer bolted on at the end.

Proving the reset worked

The auditor question is the one the whole SERP ignores: how do you prove the air reset actually did something? "We ran the gas" is not a record. A documented program is.

Air-test the room before and after. Capture mold spore counts and, where your protocol calls for it, VOC readings, so you have a before-and-after delta rather than a claim. Pull the before sample right before you activate and the after sample after the one-hour ventilation, using the same sampling location each time so the numbers are comparable cycle to cycle. One cultivation operation on the manufacturer's own testimonial wall reported that "mold levels went down 98% after our first cleaning," which is exactly the kind of measured result a log turns from an anecdote into a record you can defend. A number on a log sheet beats a memory every time an inspector asks.

Keep a reset log with the fields an auditor will want: date, room identifier, pouch size, activation time, ventilation start time, re-entry time, and operator initials. File the EPA Reg. No. 87508-2-89334 and the Safety Data Sheet in the same SOP binder, linked to the deep product detail and labels on prokuresolutions.com so the current documents are one click away at audit time. For multi-state operators, that same structure standardizes across facilities so a procurement or QA lead reads one protocol, not ten, and every room's reset reads the same way on paper regardless of which state it sits in.

Fast release vs slow release: when to reach for D instead

ProKure G and ProKure D are both chlorine dioxide gas, and growers confuse them constantly, which is a churn problem worth solving on the page. They do opposite jobs on the calendar.

ProKure G resets a room inside one turnover window. It is the fast-release gas you run during downtime, between cycles, with the room empty. ProKure D is the slow-release gas: it improves air quality and controls odors and provides ClO2 protection for up to 30 days, and it runs with plants in the room during the grow. One is the reset; the other is the maintenance hold across the run. If you landed here wanting ongoing protection during the cycle rather than the between-harvest reset, our comparison of the fast-release gas versus the slow-release 30-day gas is the page that sorts that out. ProKure D is not an EPA-registered product and is not labeled for sale as a pesticide under 40 CFR, so keep its air-quality role distinct from G's between-harvest reset. Confuse the two and you either leave a room unprotected during the grow or waste a fast-release reset trying to do a 30-day job.

Frequently asked questions

These are the questions growers ask most about the reset. Ask us anything these do not cover.

Ready to run your first reset?

Build the window into your next turnover, size the pouch to your room, and log it. When you are ready to order, ProKure G ships from prokuresolutions.com. GroClarity educates the reset; ProKure ships the product.

Related resources