ProKure G Between-Harvest Protocol: The 4-6 Hour Deep Clean

The ProKure G between-harvest protocol is a short, empty-room deep clean you run after the crop is pulled and before the next one goes in. ProKure G is an EPA-registered (EPA Reg. No. 87508-2-89334) fast-release chlorine dioxide gas, formulated for use between harvests to control odor-causing bacteria, mold, and mildew, covering 2,250 cubic feet per 25g packet. The room is empty, sealed, and treated for roughly 4 to 6 hours, then ventilated about an hour before anyone re-enters. Its label states it is not for use with/on plants, crops, or feed, so it runs unoccupied only.

What ProKure G is, and the one constraint to read first

ProKure G is a water-activated, fast-release chlorine dioxide (ClO2) gas, EPA-registered under EPA Reg. No. 87508-2-89334 and formulated for use between harvests to control odor-causing bacteria, mold, and mildew. It covers 2,250 cubic feet per 25g packet, and its deep-penetrating vapor reaches places a mop and bucket cannot. That is the appeal: an empty-room gas phase that gets into the room's geometry instead of only its surfaces.

A quick disambiguation first, because the name collides: this is ProKure the cannabis-cultivation ClO2 line, not "ProKure Digital," a separate and unrelated organization. Everything below is about the cultivation product.

Read this constraint before anything else, because it is the one that governs the whole protocol. ProKure G is for unoccupied rooms only. Its label states it is not for use with/on plants, crops, or feed, and no living plant material can be in the room during a treatment. This is not a cautious footnote; it is the line that decides when in your turnover the deep clean can happen at all. If there are plants in the room, G is the wrong product, and the plants-present cousin is ProKure D. It is a violation of Federal Law to use the product in a manner inconsistent with its labeling, so read the entire label and follow the directions for use.

Where the deep clean fits in your turnover

The between-harvest reset is a sequence, and G sits at a specific point in it. The crop comes down first: chop, defoliation, plant removal, and trim-room breakdown. Only once every piece of living plant material is out of the room does the G deep clean happen, because the unoccupied-only rule leaves no other option. After the gas phase and ventilation, high-touch surfaces get a surface pass, and then the room is reset for the next round of clones or veg transfers.

The reason the deep clean lands after plant removal, not before, is the same constraint stated as a workflow. You cannot fog a room with a crop in it, so the empty window between harvests is the only window the fast-release gas gets. That window is also when the room is at its dirtiest from a full cycle, which is exactly when a deep, penetrating reset earns its place.

What the gas phase reaches is the other reason it belongs here rather than a surface wipe. The value of a penetrating vapor over a mop is geometry: it gets behind fan blades, into HVAC ducting, under bench frames, and into ceiling seams, the places a cloth never touches and the places a spore load quietly survives a surface-only clean. A between-harvest reset that only wipes the visible surfaces leaves the room's hidden volume as a reservoir for the next cycle. The empty-room gas phase is how you treat the room, not just its benches.

What the 4-6 hour window actually looks like

This is a process-expectation page, not an activation manual, so the actual activation steps, PPE, and dispersion-cup directions live on the label and the product detail at prokuresolutions.com; follow those exactly. What you can plan around is the shape of the window. The room is emptied of plant material and sealed, with the HVAC handled per the label. The active gas phase runs for several hours while the room stays closed and unoccupied. Then there is a ventilation and off-gas period, and the room is aired out before re-entry; plan on ventilating roughly an hour before anyone goes back in, and confirm against the label for your setup.

End to end, that is roughly a 4 to 6 hour window for the sanitation portion of the turnover, start to reoccupancy. At reoccupancy, a room treated with G does not leave the rinseable residue that bleach does on hard, non-porous surfaces; verify the specifics against the label for your surfaces. The practical read for a Facility Manager is that the deep-clean portion of a between-cycle turnover compresses into part of a single shift rather than stretching across the multi-day scrub-and-rinse a bleach or quat reset can turn into.

Put that against the downtime math most single-room and small multi-room operations actually live with. A bleach or quat reset that forces a crew out on fumes, demands a rinse, and has to dry can eat three to five days of a turnover. Compressing the sanitation portion into a 4-to-6-hour unoccupied window does not make the whole turnover instant, there is still chop, breakdown, and reset around it, but it takes the sanitation step off the critical path from days to hours. Over a year of cycles, that recovered downtime is harvests you can run that the old reset was quietly costing you.

How many packets your room needs

Cultivators think in room dimensions; the label thinks in cubic feet. The conversion is the whole job. ProKure G 25g covers 2,250 cubic feet, so the math is room volume divided by 2,250, rounded up to the next whole packet. Work it from your actual room.

A 20 by 20 room with a 10-foot ceiling is 4,000 cubic feet, which is two packets. A 15 by 30 room at 10 feet is 4,500 cubic feet, also two packets. A larger flower room, say 30 by 40 at 12 feet, is 14,400 cubic feet, which rounds to seven packets. Always round up, never down: a room under-dosed for its volume is a room you did not actually treat, and the point of the between-harvest reset is that it works the first time so the next cycle starts clean. Confirm the coverage figure and any room-specific guidance on the label before you order.

Measure the real volume, not the floor plan you remember. Ceiling height is where the math quietly goes wrong, because two rooms with the same footprint and different ceilings need different packet counts, and a tall flower room holds far more air than its square footage suggests. Measure to the actual ceiling, include the full height, and treat any mezzanine or raised canopy space as part of the volume. The coverage figure is per cubic foot of air in the sealed room, so the number that matters is the one you get from length times width times height, rounded up.

Pair G with V, and hand off to D when plants return

G does the vapor phase; it is not the whole reset. The companion is ProKure V, the liquid disinfectant for hard, non-porous surfaces that kills mold and mildew at 100 ppm with a 10-minute contact time, leaves no residue, and is suitable for use with plants in the room. In a between-harvest reset, G handles the empty-room vapor and V handles the high-touch surface points, benches, tools, and door hardware, on the surface pass. The two are a system: the gas reaches the geometry, the liquid finishes the touch points.

When the room is reoccupied and clones or veg transfers go back in, G stops, because plants are present and G is unoccupied-only. The product that carries air quality forward with the crop in the room is ProKure D, the slow-release ClO2 gas that improves air quality and controls odors for up to 30 days with plants present and makes no kill claims. That is the clean division of labor across the line: G for the empty-room reset, V for surfaces, D for in-cycle air quality once the crop is back.

Keeping those three straight is where buyers most often stumble, so hold the line on it. G and D are both ClO2 gases, which is exactly why they get confused, but they are opposite tools: G is fast-release for a hard, short, empty-room reset, and D is slow-release for a low, steady, weeks-long air-quality hold with the crop present. Reaching for G when plants are in the room is a label violation; reaching for D to do a between-harvest deep clean asks a continuous air-quality product to do a reset it was never built for. Match each to its job and the line works as a system instead of three similar-looking packets.

Why cultivators move off bleach and quats

If you are skeptical that a gas beats a proven bucket of bleach, the objection is fair, and the answer is specific. Bleach and quats leave a residue that has to be rinsed, they corrode equipment over time, and their fumes often force a crew out of the room, which turns a reset into days of downtime. On the next cycle, that residue is a problem near a live crop. ProKure G's residue-free ClO2 vapor is what changes the reset: a penetrating gas phase in an empty room, no rinse step on hard non-porous surfaces, and a room that comes back online in hours rather than days. The chemistry education behind why ClO2 leaves no residue where a quat or hypochlorite does is its own topic, worth reading if the bleach habit is the thing holding your turnover hostage.

The failure pattern worth naming is the grower who switches off bleach, keeps the same surface-only habits, and still fails a yeast and mold test, then blames the new product. The miss is not the chemistry; it is treating a between-harvest reset as a wipe-down when the room's hidden volume, the ducting and the seams, is where the load actually lives. The point of the fast-release gas phase is to treat that volume, which a surface routine, bleach or otherwise, never reaches. Change the method, not just the bottle.

The compliance data trail you can hand an auditor

A between-harvest deep clean is also a record, and the record is what a state auditor reads. Log each deep-clean event: the date, the room ID, the number of packets used, the dwell time, and a post-clean surface swab or air sample if you run one. That trail does two jobs. It proves the sanitation portion of the turnover actually ran, on the date it ran, in the room it ran in, which is exactly what a compliance inspector asks for. And it ties the deep clean back to the pre-sale yeast and mold test that a failed harvest turns into a six-figure loss, so the record is both an audit defense and your own evidence that the program is working. The top search results for this protocol are product pages and a how-to video; none of them give you the log structure, which is the part a Head Grower or a multi-facility Cultivation Director actually needs.

For a multi-state operator, the same log structure is what makes a protocol portable. One template for the deep-clean event, filled identically in every room and every state, means a Cultivation Director can defend the same record to a Colorado inspector and a Michigan one without reinventing the paperwork each time. The protocol that survives a staff change and a state line is the one that was written down the same way everywhere, and the deep-clean log is the smallest, highest-value piece of that discipline. It costs a few fields per event and it is the first thing an auditor asks to see, which makes it the cheapest insurance in the whole turnover.

To order ProKure G, see the product detail, label, SDS, and EPA registration record at prokuresolutions.com, and shop the ClO2 line on shop.groclarity.com. For a between-harvest protocol designed and standardized across your facilities, with the data trail built in, request a quote from GroClarity.

Related resources