How ProKure G Resets Grow-Room Air Between Harvests (4-6 Hour ClO2 Treatment)
ProKure G is the fast-release ClO2 gas you run in an empty grow room between harvests to reset the air. It works in 4 to 6 hours, you ventilate for one hour before re-entry, and it runs only in an unoccupied space with no people, pets, or plants present, because its label reads 'Not for use with/on plants/crops/feed.' ProKure G is EPA-registered (EPA Reg. No. 87508-2-89334), and its approved claim is the solution to mold and mildew, odor-causing bacteria, and chemical odors. Its deep-penetrating vapor reaches the returns and corners a wipe-down misses. This page is about that reset: the window, the steps, the coverage math, and the HVAC call.
What ProKure G actually is
ProKure G is a fast-release chlorine dioxide gas, and the word fast is the whole distinction from the rest of the line. Where the slow-release product holds a trace-level layer for weeks, G releases a high-output burst of ClO2 vapor that resets a room's air in a single 4-to-6-hour treatment. It is a between-harvest tool, not a maintenance layer.
State the one line that governs everything else up front: its label reads not for use with/on plants/crops/feed, and people and pets must not be in the area during treatment. ProKure G runs in an unoccupied space. There is no version of this product that runs around a live crop, and confusing that is the single most consequential mistake in the ProKure line, because applying an EPA-registered product against its label is a violation of federal law regardless of intent.
The compliance side is actually a point in G's favor, stated plainly. ProKure G is EPA-registered under EPA Reg. No. 87508-2-89334. That registration, and the verbatim label language that comes with it, is what goes in your compliance file. Its approved claim is specific: it is the solution to mold and mildew, odor-causing bacteria, and chemical odors, delivered as a deep-penetrating ClO2 vapor. Keep the claim exactly that broad and no broader; G controls the odor-causing and mold-and-mildew load in the air of an empty room, and the heavier surface-disinfection kill work belongs to the liquid, covered below.
Why a gas at all, when you could wipe a room down? Because air is not a surface. ClO2 gas is a small molecule that fills a space evenly and creeps into the returns, ducts, corners, and gaps a mop or sprayer never reaches. That is the job G does that a liquid cannot: it treats the whole air volume of the room, not just the surfaces you can physically touch.
When to run G: the between-harvest window
The name of the query says it: between harvests. G runs in the gap when a room is stripped and empty, before the next crop goes in, and its place in a turnover sequence is specific.
Here is where it sits. You harvest and strip the room. You disinfect the hard surfaces, benches, trays, tools, with the liquid surface disinfectant, because surfaces are their own job. Then, with the room empty of plants and people, you run the ProKure G gas reset to knock the room's airborne load back to a clean baseline. You ventilate, re-enter, and then the next crop goes in and the slow-release air layer takes over for the grow. G is the reset event that brackets the cycle, not something that runs during it.
There is a compliance pressure behind the timing. A cultivator is judged by a state lab on whether finished flower passes a total yeast and mold test, and the airborne load a room carries between crops is part of what seeds the next cycle's pressure. Resetting the empty room's air before repopulating it is a way to start the next crop from a cleaner baseline. The air reset is not the finished-product test and not a substitute for it, and state action limits vary by market, so confirm your own thresholds with your state regulatory agency; the reset is one input to keeping the room's conditions in your favor.
The reason a grower reaches for a 4-to-6-hour gas treatment rather than a multi-day scrub is downtime. A between-cycle turnover that drags on for days is lost production, and the appeal of the gas reset is that the air portion is measured in hours, not days. The next section puts real numbers on that window.
The four-step activation protocol
The activation is four steps, straight from the label, and getting them exactly right is the difference between a clean reset and a wasted treatment.
Step one: tear open the foil package and remove the white inner pouch. Do not open the white inner pouch. The pouch is the ClO2-generating system and it stays sealed.
Step two: place the end of the white pouch that has the square indentations into the reusable gas dispersion cup filled with 1.5 inches of water. The water is what activates the release. The dispersion cup is reusable for future treatments, which matters for cost over a year of turnovers.
Step three: set the cup on a stable, level surface in a high, central location in the room, and turn off the lights. Make the HVAC decision here (the next section walks it). This placement and the lights-off step are not optional flourishes; they are how the gas distributes and works.
Step four: allow at least 4 to 6 hours for the system to work, then ventilate and turn on the lights for one hour before anyone re-enters. Repeat the treatment if odors reappear. That one-hour ventilation before re-entry is the safety step that is not negotiable, because the room has to clear before a crew goes back in.
Use the caution placards included with the product to mark the treatment start and the safe re-entry time, so no one walks into a room mid-treatment. That placard, with the date and times filled in, doubles as a compliance artifact: it is evidence the treatment ran, for how long, and when the room was cleared.
Coverage math for real grow rooms
The SKUs are rated by air volume, and translating that into your actual room is the arithmetic the product pages leave to you.
A 25g packet covers approximately 2,250 cubic feet. A 10g packet covers approximately 1,000 cubic feet. Coverage is cubic volume, length times width times ceiling height, because the gas fills the room to the ceiling, not floor area.
Work it for real rooms. A 10-by-10-by-10-foot room is 1,000 cubic feet, one 10g packet. A 20-by-20-by-10-foot room is 4,000 cubic feet, which takes two 25g packets (2,250 cubic feet each) to cover with margin. A larger 30-by-40-by-12-foot bay is 14,400 cubic feet, which is seven 25g packets. The rule when a room exceeds one packet's coverage is to place packets equally apart so the gas distributes across the whole volume rather than concentrating in one spot.
Size to the room and round up, the same discipline as any ClO2 product: a room covered short runs a thin reset no matter how long you leave it, and the point of a reset is to actually clear the air volume, not most of it. Do the cubic math once per room and write the packet count into the room's turnover checklist so no one is doing arithmetic during a strip-out.
The HVAC and placement decisions
Two on-site decisions make or break the treatment: what you do with the air handler, and where you set the cup.
Start with HVAC, because it is the one the product pages gloss in a single sentence. The rule has a fork. If the HVAC system serves only the room being treated, turn on the air conditioning or ventilation to circulate the gas through the space, which helps distribute it. If the system is shared with another room, turn it off and close the ducts, so you are not pushing ClO2 gas into an adjacent room, especially one with a crop in cycle. A shared plenum is exactly how an unoccupied-room treatment becomes a problem in an occupied one, so when in doubt on a shared system, isolate the treated room before you activate.
Placement follows the physics. ClO2 gas is heavier than air, so set the activated cup in a high, central location and let the gas fall through the room's volume. Keep it no closer than 18 to 24 inches from fabrics, leather, electronics, mirrors, metals, or plated surfaces. A fan or air mover in the room helps increase circulation and distribute the gas evenly, which matters more in a large or irregular space where a single central point would otherwise leave dead zones. Electronics and equipment surfaces do not need to be removed or powered down for the treatment, and furniture can stay; the clearance rule is about keeping the activated unit itself a safe distance from those materials, not about stripping the room.
G, D, and V: the reset, the maintenance, the wipe-down
G does one job well, and a grower gets the most out of it by knowing where it ends and the other two products begin. The clean mental model: G is the reset, the slow-release gas is the maintenance, and the liquid is the wipe-down.
ProKure G is the between-harvest air reset in an empty room. Once the room is reset, ventilated, and repopulated with the next crop, the slow-release ProKure D takes over as the continuous, plants-in-place air-quality layer: it improves air quality and controls odors and provides ClO2 protection for up to 30 days, and unlike G it runs with the plants in the room. The two are a pair by design, G resets the empty room, D holds the line through the grow, and no single competing page tells that story even though it is the whole point of running both.
Surfaces are the third job, and they belong to ProKure V, the liquid Hospital-Type Disinfectant for hard, non-porous surfaces. In a turnover, V and G run in sequence, not in competition: wipe the hard surfaces with V, then run the G gas reset on the empty room's air. V is suitable for use with plants in the room and leaves no residue, so it also covers spot surface work, while G handles the air volume a liquid cannot reach. Three products, three jobs, one sequence. The sibling product pillars carry the full detail when your question moves to the maintenance layer or the surface work.
Compliance, PPE, and the downtime math
Three practical questions close out the reset: what to document, what the crew needs to wear, and how long the room is actually down.
On documentation, the treatment produces its own compliance trail if you let it. The caution placard with the activation time and the safe re-entry time, kept with the room's turnover log, is evidence the air reset ran on schedule. Pair that with the product label and SDS on file, and an auditor asking whether the room was treated has a dated record rather than a verbal assurance. The authoritative label, SDS, and EPA registration references live on prokuresolutions.com for your binder.
On PPE, the honest answer follows from the unoccupied-room rule. Because ProKure G is intended for a space with no people or pets present during treatment, PPE is not required for the treatment itself. That said, chlorine dioxide gas can irritate the respiratory tract, which is exactly why the room stays empty during the dwell and gets a full hour of ventilation before re-entry. Follow the label, use the placards, and the no-PPE answer holds because no one is in the room while the gas is active.
On downtime, do the math the product pages never finish. The treatment is 4 to 6 hours, plus one hour of ventilation before re-entry, which is a room-lock window of roughly 5 to 7 hours, plus your prep and strip-out time. For a facility manager building a shift schedule, that means the air reset fits inside a single extended shift or an overnight run rather than eating days. Run it overnight with the lights off, ventilate in the morning, and the room is ready for the next crop the same day, which is the difference between a turnover measured in hours and one measured in days.
To run a between-harvest reset, reorder ProKure G on shop.groclarity.com, pull the label and SDS from prokuresolutions.com for your compliance file, and for a multi-facility turnover protocol or account-level pricing, talk to a GroClarity specialist through the contact form. See the product label for specific instructions and claims.
Related resources


