How to Use ProKure G: Step-by-Step Activation and Between-Cycle Protocol

To use ProKure G, first confirm the room is unoccupied with no plants in it, because ProKure G is not for use with or on plants, crops, or feed. Then tear the foil packet, place the white inner pouch indentations-down in a plastic cup holding 1.5 inches of water (do not open the white pouch), and set the cup high and central in the room, 18 to 24 inches from fabrics, leather, electronics, mirrors, and metal. Turn off the lights, leave it to work for 4 to 6 hours, then ventilate for one hour before anyone re-enters. The rest of this page is the sizing, placement, timeline, and compliance detail around those steps.

Before you open the packet: is this the right room for ProKure G

The single most important check happens before activation, and getting it wrong is the top failure mode. ProKure G is a fast-release ClO2 gas for empty rooms. People, pets, and plants must be out during treatment. The label is explicit that it is not for use with or on plants, crops, or feed. If there is a live crop in the room right now, stop: you want ProKure V for surfaces with plants present, or ProKure D for ongoing air quality with the crop in the room. For the full product decision, see our ProKure V and ProKure G comparison.

The packet decision is a volume calculation, not a floor-area one, because the gas fills the whole cubic volume. Measure length times width times height. The 10g pouch covers roughly 1,000 cubic feet; the 25g pouch covers about 2,250 cubic feet for standard odors, and less for heavy odors, where the label calls for a higher dose per hundred cubic feet. A small drying room at 8 by 8 by 10 feet is 640 cubic feet, a single 10g job. A 20 by 15 by 10 foot flower room is 3,000 cubic feet, which runs past one 25g packet, so you use two 25g pouches placed apart rather than stretching one. When a measured volume lands near the top of a packet's range, step up or add a pouch instead of running one thin.

Have the kit staged before you tear anything: the packet, a plastic cup, water to a depth of 1.5 inches, the enclosed caution placard, and a fan if you want faster distribution. Stage the documentation too, because the treatment record is part of the job, not an afterthought.

Step-by-step activation

Work the four steps in order. They are short, and the detail is in doing each one exactly.

Step one: tear open the foil packet and remove the white inner pouch. Do not open the white pouch. It is designed to react through its membrane in contact with water, and opening it defeats the system and creates a hazard.

Step two: place the end of the white pouch that has the square indentations into a plastic cup filled with 1.5 inches of water. Less than 1.5 inches is a common error that starves the reaction. The pouch stays sealed in the water.

Step three: placement, which has three rules that work together. Set the cup high and central, because chlorine dioxide gas is heavier than air and will settle and fill the room from a high point, so a cup on the floor lets the gas pool low and leaves the upper room under-treated. Keep it 18 to 24 inches away from fabrics, leather, electronics, mirrors, metals, and plated surfaces. Turn off the lights, since the system works best in the dark. For ventilation, if a system is dedicated solely to the room being treated, set it to recirculate; otherwise turn the system off and close the ducts so the gas stays in the room. A fan or air mover inside the room improves distribution.

Step four: leave it to work for 4 to 6 hours, or overnight. Then ventilate and turn the lights on for one hour before re-entry. Record the treatment start and the safe re-entry time on the enclosed caution placard. Repeat the treatment if odors reappear.

The room-turnover timeline, hour by hour

The retail listings bury the timing inside a step, so here it is as a schedule a facility manager can plan a turn around.

Hour zero: room confirmed empty, packet activated, cup placed high and central, lights off, placard filled in with the start time. Hours one through six: the dwell window, with nobody entering. For routine between-cycle odor and air work, 4 to 6 hours is the range; overnight is fine when the turn allows it. After the dwell, run a one-hour ventilation with the lights on. Re-entry happens at roughly hour seven, and the room is ready for the next cycle's setup at hour eight. On a tight turn, activating overnight collapses the whole window into downtime you were not using anyway.

Ceiling height changes the feel of it. A tall room has more vertical volume for the gas to fill from the high point, so active air movement earns its keep more in a 12-foot room than an 8-foot one, and a very large volume is a cue to split the dose across placed pouches rather than lean on one.

Ventilation, HVAC, and deodorizing a duct system

Airflow is the part most protocols underexplain, and it changes depending on your HVAC layout.

If the ventilation system serves only the room you are treating, set it to recirculate so it moves the gas around the space instead of exhausting it. If the system is shared with other rooms, turn it off and close the duct to the treatment room, so you are not pushing ClO2 into occupied space. Either way, a fan or air mover inside the sealed room improves even coverage into corners.

The duct system itself can be deodorized with ProKure G, and the label sets a hard ceiling for that use: before activating, make sure the ventilation system is off or set to recirculation, clean the duct work first, do not exceed 500 ppm, and allow one hour to ventilate before re-occupation. That 500 ppm ceiling is specific to the empty-room duct-deodorizing procedure; do not generalize it to other uses.

EPA compliance and the required disclaimer

ProKure G is an EPA-registered product (EPA Reg. No. 87508-2-89334), and with registration comes a label you are legally bound to follow. For a licensed cannabis facility, the Q40 worry, this is where it lands.

The disclaimer to internalize is not for use with or on plants, crops, or feed. In plain terms, ProKure G treats an empty room's air between cycles; it is not applied to the crop and the crop is not present during treatment. Using an EPA-registered product in a manner inconsistent with its labeling is a violation of federal law, so running ProKure G with plants in the room is not a shortcut, it is a compliance problem.

The caution placard is the audit artifact that proves you did it right. Recording the treatment time and the safe re-entry time on the enclosed placard, and keeping that record with the room's log, is exactly the kind of documentation a state review wants to see. Keep the product label and SDS on file as well, pulled from prokuresolutions.com, so procurement and QA have the registration record for the audit binder. This is general process guidance, not legal advice; confirm your state's rules with your compliance lead.

When one treatment is enough, and when to escalate

For routine between-cycle odor and air work in an empty room, a single ProKure G treatment is typically enough, and the label's own instruction is simply to repeat the treatment if odors reappear.

Persistent odors after a correct treatment are a signal, not just a nuisance. If odor returns quickly, the underlying source was not fully removed, which means the room needed a surface clean before the air reset, or there is an ongoing contamination source the gas cannot fix. That is the point to step back to a full between-cycle protocol rather than re-dosing the air repeatedly. Our mold prevention protocols hub covers the surface-plus-air routine a persistent problem actually needs.

The common mistakes are worth naming plainly, because each one wastes a treatment: placing the cup on the floor so the heavier-than-air gas pools low, opening the white inner pouch, using less than 1.5 inches of water, skipping the one-hour ventilation before re-entry, and running with plants still in the room. Avoid those five and the protocol does what it should.

Where ProKure G fits with V and D

Keeping the three products in their lanes is both the compliance point and the performance point, so here is the clean division.

ProKure G is the fast empty-room reset. It works in 4 to 6 hours and is the solution for mold and mildew, odor-causing bacteria, and chemical odors between harvests, in a room with no plants in it.

ProKure V is the liquid for surfaces. It is an EPA-registered hospital-type disinfectant for hard, non-porous surfaces, suitable for use with plants in the room, and it leaves no residue. When the job is disinfecting benches and tools, that is the ProKure V surface disinfectant.

ProKure D is the slow-release gas that holds air quality, improving air quality and controlling odors for up to 30 days with the crop present. For ongoing in-cycle air, that is the ProKure D air-quality protocol.

G resets the empty room fast, V disinfects surfaces, D holds the air over weeks. Once the room is reset, buy and reorder ProKure G on shop.groclarity.com, and route multi-facility standardization questions to a GroClarity specialist through the contact form. See product label for specific instructions and claims.

Related resources