How to Mix ProKure V: Chlorine Dioxide Mixing Instructions by SKU
To mix ProKure V, you do not measure anything. Each pouch is pre-portioned to hit 100 ppm in a set water volume, so the job is matching the pouch to the water and giving it time to activate. Tear the foil, remove the sealed white inner pouch (do not open it), drop it into an opaque container filled with the water amount for that pouch size, and agitate one minute every 15 minutes until full strength at one hour, five agitations in all, water held at 20 to 25 degrees C. That yields a 100 ppm chlorine dioxide (ClO2) solution for hard, non-porous surfaces. This page walks each pouch size and its safety steps.
Before you mix, the pre-flight checklist
Start with what is in the pouch and what it is for. ProKure V is a water-activated ClO2-generating disinfectant, labeled as a hospital-type disinfectant for hard, non-porous surfaces. It is suitable for use with plants in the room and leaves no residue, which is why cultivators reach for it on between-cycle surface turnover. Read the one line that governs everything else: this is a surface disinfectant. It is not a drinking-water product and not an oral product, and nothing on this page is dosing guidance for human consumption.
That distinction matters because most chlorine dioxide content online is written for a different and unregulated use. The top-ranked mixing guides describe two-part drop-by-drop activation for drinking water and so-called MMS protocols. One of those guides admits the drop size can vary by up to 250%, which tells you everything about the precision of that approach. The same vendor concedes that for the classic two-part product, dosage is only possible to a very approximate degree. That is the opposite of what a cultivation facility needs. A grow room running to a state microbial threshold cannot afford a disinfectant whose working concentration swings by a factor of two depending on how a drop falls. ProKure V sidesteps all of it with a sealed, pre-measured pouch that carries the ratio inside the packet, so the only variables left to you are water volume, temperature, and time.
PPE: the dry pouch ingredients are corrosive, so wear protective eyewear such as goggles or a face shield, wear gloves, and activate in a well-ventilated area. Do not open the white inner pouch; the system is designed so you never contact the dry ingredients under normal use, and that design is also your safety margin. Ventilation and re-entry follow the label for the space you are treating. Do not combine ClO2 with bleach, ammonia, quats, or acids. The dry sodium chlorite is not compatible with any reducing agents, combustible materials, solvents, acids, paints, or sulfur-containing rubber, and mixing incompatible chemistries is how people generate dangerous gas concentrations. Keep the activated solution away from heat, sparks, and light, and dilute or work with it in an open, well-ventilated area. None of this is onerous once it is a habit; it is the same discipline any EPA-registered oxidizer asks for.
Water and container specification
The container is part of the recipe. Use an opaque, not clear, container, because light degrades the activating solution. Keep the water temperature between 20 and 25 degrees C; colder water slows activation and warmer water is outside the label window. Use clean water and a container with enough headspace to agitate without spilling.
Chlorine dioxide is a strong oxidizer, so container material matters. Compatible materials include high-density polyethylene (HDPE), polypropylene (PP), CPVC, and glass. Avoid metal containers, containers and fittings that oxidize or react, and anything you cannot dedicate to the task, and never reuse a food or beverage container for the activated solution. The label is explicit that the dry pouch must be kept away from water, acid, heat, and open flame until you are ready to activate, and that the pouch cannot come into contact with water or acid-based products in storage. One more practical note: size the container to the pouch. You want enough headspace to agitate vigorously for a full minute without sloshing solution out, because weak agitation is a common reason a batch reads low at the one-hour mark.
ProKure V 20 gallon pouch
The largest cultivation pouch is the 3.36 oz (95.2 gram) packet. Add one 3.36 oz pouch to 20 gallons (75.7 L) of water in an opaque container to reach 100 ppm. Tear the foil, remove the white inner pouch without opening it, and drop it in. Agitate for one minute, then again at 15, 30, 45, and 60 minutes, five one-minute agitations across the hour. Allow the full hour before use so the solution reaches full strength. Confirm with a chlorine dioxide test strip if you want a reading, and remember the target is 100 ppm for hard, non-porous surface disinfection at a 10-minute contact time. This is the batch size for a full-room turnover: enough solution to keep every bench, wall section, and piece of equipment visibly wet through the contact window without stopping to remix. If you need a lighter concentration for a sanitizing pass rather than a full disinfection, the label allows diluting the 100 ppm solution (1:5 to reach 20 ppm, 1:20 to reach 5 ppm), but mix to 100 ppm first and dilute from there rather than under-dosing the pouch.
ProKure V 5 gallon pouch
The 0.84 oz (23.8 gram) pouch makes 5 gallons (18.9 L) at 100 ppm. Same procedure: foil off, white pouch in (sealed), opaque container, 20 to 25 degrees C. Agitate one minute on addition and at each 15-minute mark through the hour, five agitations total, then wait the full hour for full activation. This is the common mid-size batch for a single room or a run of tools and benches, enough working solution to keep surfaces visibly wet for the 10-minute contact time without mixing a 20-gallon drum you will not finish. A five-gallon bucket is also the easiest batch to agitate by hand, which matters, because the agitation is not optional stirring, it is what drives the activation reaction to full strength on the label's schedule.
ProKure V 1 gallon pouch
The 0.17 oz (5 gram) pouch makes 1 gallon (3.7 L) at 100 ppm. Procedure is identical and the small batch is the point: mix what you will use so you are not storing excess. Foil off, sealed white pouch into an opaque one-gallon container of 20 to 25 degree C water, agitate one minute at addition and at 15-minute intervals to the one-hour mark, then use. A gallon covers spot turnover, drop-down hoses, and tool sanitation without waste.
ProKure V 1 quart pouch
The smallest pouch, 0.042 oz (1.19 grams), makes 1 quart (946 mL) at 100 ppm. This is the touch-up size for a single surface, a glove and shoe dip refresh, or a small tool set. Drop the sealed white pouch into an opaque quart container of clean 20 to 25 degree C water, agitate one minute now and at each 15-minute interval through the hour, and give it the full hour. The pre-portioned pouch means a quart is as precise as a 20-gallon drum; the ratio is built into the packet.
Quick-reference mix ratio table and failure modes
Here is the whole card. The 3.36 oz (95.2 g) pouch goes in 20 gallons. The 0.84 oz (23.8 g) pouch goes in 5 gallons. The 0.17 oz (5 g) pouch goes in 1 gallon. The 0.042 oz (1.19 g) pouch goes in 1 quart. Every pouch targets 100 ppm, every mix uses an opaque container at 20 to 25 degrees C, and every mix needs five one-minute agitations across one hour before use. One pouch, one water volume, one hour. That is the card.
Now the ways a mix goes wrong. A correctly activated solution is a light, clear yellow with a faint chlorine odor. If you skipped the activation timer and used it early, it has not reached full strength and will underperform at the surface, so give it the full hour even when you are in a hurry. Weak or off color usually means the water was too cold, the container let in light, or the hour was not respected; remix following the temperature and opaque-container steps. An under-dissolved or slow mix most often traces back to water below 20 degrees C or agitation that was too gentle to work the pouch. If you suspect a problem, a test strip reading against the 100 ppm target settles it in seconds. Do not try to rescue a bad batch by guessing at more product, and never add a second pouch to a container that already holds one; the pouch is the dose, and doubling it does not double a known concentration, it just creates an unknown one. When in doubt, dump and remix. A fresh pouch costs less than a surface treatment that quietly failed.
Applying, storing, and documenting the mixed solution
Apply the 100 ppm solution to hard, non-porous surfaces (grow beds, drying rooms, cure rooms, vegetation and propagation rooms, mother rooms, trimming areas, tools, and drop-down hoses) by mop, sprayer, or sponge, pre-cleaning visibly soiled surfaces first with a non-disinfectant cleaner so the ClO2 is not spent on grime. Keep the surface visibly wet for the full 10-minute contact time, reapplying if it dries early, because contact time is the part growers skip and it is the part that does the work. ProKure V leaves no residue on these surfaces, which is the reason it fits a grow room where a residual film would become its own chemical-contamination problem. It is also labeled as suitable for use with plants in the room, which bleach and quats cannot claim, so you are not evacuating the canopy to sanitize surfaces nearby.
Activated solution does not keep indefinitely, so treat shelf life as part of the plan rather than an afterthought. Store any unused activated solution in a dark, closed or sealed container in a cool, dark place away from sunlight and separate from any food, record the activation date on the container, and use it within 15 days of activation, then dispose of it per the label. The practical takeaway is to mix to the batch you will actually use in that window. A 20-gallon drum you only half-empty is wasted product and a storage headache; the four pouch sizes exist precisely so you can right-size the batch to the job, from a full-room turnover down to a single-tool touch-up. Dispose of spent solution and the empty packaging according to the label and local regulations, and discard the empty foil and spent pouch in an outdoor refuse container. For a compliance audit, log the pouch SKU, the water volume, the activation date and time, the target 100 ppm, and the rooms and surfaces treated. That activation log plus the EPA label and SDS is the documentation a state inspector expects. GroClarity builds that record-keeping into its sanitation SOPs from Phoenix, AZ at 5013 E. Washington St. Ste. 130, Phoenix, AZ 85034, 866.206.1301. Order ProKure V on shop.groclarity.com; find the full label and SDS on prokuresolutions.com.
Related resources
Related resources


