Chlorine Dioxide Dilution Chart for Cannabis Cultivation (ProKure V, D, G by SKU)
A cannabis grower searching for a chlorine dioxide dilution chart has already decided to use ClO2 and now needs the math: which ProKure V packet, how much water, and how to step the activated 100 ppm stock down to a lower working concentration. ProKure V (EPA Reg. No. 87508-3-89334) ships in four packet sizes, 3.36oz, 0.84oz, 0.17oz, and 0.042oz, and each one activates to 100 ppm at its labeled water volume: 20 gallons, 5 gallons, 1 gallon, and 1 quart in order. From that 100 ppm stock, a dilution device gives you 20 ppm at 1:5 and 5 ppm at 1:20.
That is the whole chart, and the rest of this page is the fine print around it: when each concentration is label-permitted, how contact time pairs with ppm, and what shifts your real-world reading. Dilution is a ProKure V (liquid) question. ProKure D and ProKure G are gases, dosed by the cubic feet of the room, not by ppm in water, and they carry roughly 90 percent of grower orders. If you came here for gas dosing, the gas section below points you to the right product.
ClO2 is not CO2, and liquid is not gas
Two things get confused on this query. The first is the acronym. Chlorine dioxide is ClO2, a disinfectant chemistry. Carbon dioxide is CO2, the gas you enrich a canopy with for photosynthesis. They are unrelated, and a "dilution chart" only makes sense for ClO2. If you are tuning a canopy CO2 setpoint in parts per million of air, this is the wrong page.
The second is form. ClO2 reaches a grow room two ways, and only one of them dilutes in water. ProKure V is the liquid: a water-activated packet that generates a chlorine dioxide solution you measure in ppm. ProKure D and ProKure G are gas-release systems you size by room volume in cubic feet. A dilution chart is a liquid instrument. Keep the gases out of the ppm math entirely, or you will dose a room wrong.
Where to go if you need gas dosing instead
ProKure G is the fast-release gas for deep cleaning between harvests, working in 4 to 6 hours, with the label disclaimer "Not for use with/on plants/crops/feed." ProKure D is the slow-release gas that provides ClO2 protection for up to 30 days and improves air quality and controls odors. Both are dosed by cubic feet: the G 25g pouch covers about 2,250 cubic feet for standard odors, the D 95g pouch about 8,000 cubic feet. For those, use the product pages rather than this chart.
The core ProKure V dilution chart (the money table)
Here is the artifact the top search results never print. Each ProKure V packet is engineered to hit the same 100 ppm activation concentration, so the only decision is batch size: how much finished solution you need at the mix station.
| ProKure V packet | Water to activate | Yields at 100 ppm | --- | --- | --- | 3.36oz (95.2 g) | 20 gallons (75.7 L) | 20 gallons of 100 ppm stock | 0.84oz (23.8 g) | 5 gallons (18.9 L) | 5 gallons of 100 ppm stock | 0.17oz (5 g) | 1 gallon (3.7 L) | 1 gallon of 100 ppm stock | 0.042oz (1.19 g) | 1 quart (946 mL) | 1 quart of 100 ppm stock |
Activate the pouch in an opaque (not clear) container with the correct amount of water, then agitate for one minute at 15-minute intervals until full activation at one hour, five agitations in total. The label is explicit here: allow one hour before use so the solution reaches full strength, and keep the water between 20 and 25 degrees Celsius.
How to pick the packet by batch size
Match the packet to the vessel, not the facility. A single trimmer bench or a tool-dip jar runs on the 0.042oz quart or the 0.17oz gallon. A room turnover with mop buckets and sprayers steps up to the 0.84oz five-gallon batch. A large multi-room sanitation pass uses the 3.36oz twenty-gallon packet. Activating a 3.36oz packet for a 4-by-8 room wastes most of the stock, because an activated solution has a 15-day working life. Record the activation date on the container and discard stored solution after 15 days.
Step-down dilution from 100 ppm stock to a working solution
The 100 ppm activation is your stock. For lower-concentration label uses, the ProKure V label gives two dilution ratios off that stock, using a dilution device or sprayer:
| Target concentration | Dilution ratio | Label use example | --- | --- | --- | 100 ppm | none (use stock) | Disinfect hard, non-porous surfaces, 10-minute exposure | 20 ppm | 1:5 (1 part stock, 4 parts water) | Sanitize hard, non-porous surfaces, 5-minute exposure | 5 ppm | 1:20 (1 part stock, 19 parts water) | Food-contact sanitizing and root-zone and cut-flower dip uses |
Notice what is not on this list. There is no 500 ppm "shock" dilution for ProKure V liquid, because the label does not authorize one; the highest surface concentration on the label is the 100 ppm disinfection use. If a protocol you found elsewhere calls for 500 ppm or 2,000 ppm in water, that is a different chemistry or a non-ProKure procedure, and it is outside this product's directions. Use the label concentration or do not make the claim.
20 ppm for root zone and irrigation
The 5 ppm and 20 ppm range is where ClO2 touches living plant systems rather than empty surfaces. For root-zone and irrigation work, dose the clean feed tank to the final concentration your protocol calls for rather than pouring stock in blind. GroClarity's root-zone page already covers the 20 ppm feed-tank method and the runoff target in detail, so use the chart here to mix the stock, then follow that page for the irrigation protocol itself.
Contact time is the other half of every number
ppm alone does not disinfect. The ProKure V label pairs each concentration with an exposure time, and the surface has to stay visibly wet for the full window. At 100 ppm, the disinfection exposure is 10 minutes on hard, non-porous surfaces. At that condition the label fungicide claims include Fusarium solani (ATCC 36031), Botrytis Sp and Penicillium digitatum (ATCC 201167), and Aspergillus niger (ATCC 9642), the mold and fungal targets a cultivation facility actually fights. SARS-CoV-2 is a 30-second claim at 100 ppm. Food-contact sanitizing drops to one minute at 5 ppm.
So for the cannabis pathogens most growers ask about, powdery mildew and Botrytis among them, the operating point is a 100 ppm surface solution held wet for 10 minutes, not a quick spray-and-wipe that flashes off in two. A thin film on warm steel can evaporate before the window closes, which is why a soak or a re-wet matters more than the headline ppm. Prevention is the posture that pays, and the number a head grower loses sleep over is the state pre-sale yeast and mold threshold, not the mix ratio.
Water quality and verifying your actual ppm
The chart assumes clean water and a correct activation. Two things pull your real reading off target. Alkalinity and starting pH shift how the chemistry behaves, and a heavy organic load, a dirty reservoir, or visibly soiled surfaces consume ClO2 before it reaches the target, which is why the label says to pre-clean soiled surfaces with a non-disinfectant cleaner first.
The fix is to measure, not assume. Chlorine dioxide test strips or a photometer confirm you are actually near 100 ppm at the station rather than trusting the mix. For a standing tool-soak jar, that matters more over time, because ClO2 concentration drifts down across the 15-day working life. A jar mixed three weeks ago is not disinfecting at 100 ppm today, which is the reason for the 15-day discard rule in the first place.
EPA compliance notes to read before you mix
EPA compliance is the worry cultivators name first, so treat the ppm as inseparable from the permitted use. ProKure V is the EPA-registered product here, Reg. No. 87508-3-89334, and it carries the disinfectant, virucide, fungicide, and sanitizer claims at their labeled concentrations and exposure times. The two gases are governed differently. ProKure G (EPA Reg. No. 87508-2-89334) carries "Not for use with/on plants/crops/feed," and ProKure D is "Not an EPA-registered product and not labeled for sale as a pesticide under 40 CFR." Keep each product's claim with that product.
For the audit trail, every SKU's SDS and full label lives on prokuresolutions.com, which is where a procurement or QA lead should pull the documentation for a compliance binder. The standing rule above the chart: "It is a violation of Federal Law to use this product in a manner inconsistent with the labeling." Read the entire label and use strictly in accordance with its precautionary statements. When your SOP and the label disagree, the label wins.
Put the chart to work
Mix from the table, hold the exposure time, verify with a strip, and discard the stock at 15 days. That is the entire operating loop. Educate here on groclarity.com, order and reorder ProKure V on shop.groclarity.com, and pull every label and SDS from prokuresolutions.com. See product label for specific claims and instructions. Built on Science. Backed by Results.
Related resources


