A yeast and mold count is only useful if you know what to do with the number. Total Yeast and Mold Count (TYMC) limits range from 1,000 CFU/g in the strictest states to 100,000 CFU/g in the most lenient, so your first move is to read the result against your own state's threshold. From there the response is banded: well under the limit means document and release; trending upward means quarantine and reset the room; at or over the limit means hold the batch, isolate the room, and follow your state's failure path. This page gives the action for each band and the audit trail an inspector expects.

Read your number against your state's limit first

The same CFU count can pass in one state and fail in another. Published limits for total yeast and mold range from 1,000 to 10,000 CFU/g in the strict jurisdictions up to 50,000 to 100,000 CFU/g elsewhere, and some states, like California, instead test for specific pathogens such as the four regulated Aspergillus species at zero tolerance. Before you react, confirm three things: your state's TYMC limit, whether it also runs a pathogenic Aspergillus panel, and whether it permits remediation. Those three facts determine which band below applies.

The response, banded by CFU result

Under roughly 50 percent of your limit: document the result, log the batch, and release. Keep the COA in the batch record. Between 50 percent and your limit: treat it as drift. Quarantine the batch pending a confirmatory retest, pull an in-house plate or air sample to find the source, and run a between-cycle air-quality reset before the next cycle. At or over the limit: this is a fail. Place the batch on hold, isolate the room, stop moving product out, and open the failure path your state defines. Do not rewash or reprocess flower to chase a number; that is not a sanctioned fix and it corrupts your record.

The first 24 to 72 hours after a positive COA

Hour 0 to 24: isolate the affected batch and tag it on hold, quarantine the room it came from, and notify your QA lead and, where your state requires it, the regulator. Start the response log. Hour 24 to 72: order a confirmatory retest through your lab, pull the chain-of-custody paperwork, and identify the likely source (air, water, substrate, curing, or handling) with in-house sampling. Week 1: execute the sanitation reset, re-test, and record the batch disposition. A time-boxed sequence is the difference between a contained event and a facility-wide loss.

TYMC versus Aspergillus versus total aerobic count

These are different tests measuring different things, and each failure points somewhere different. A high TYMC usually signals a cultivation or post-harvest humidity and airflow problem. A pathogenic Aspergillus hit points at environmental sourcing, often HVAC, drains, or substrate. A high total aerobic count can indicate water-source or handling contamination. Reading which test failed tells you where to look, so you fix the root cause instead of blanket-treating the whole facility and hoping.

The sanitation reset and the EPA lanes

When you reset a room, keep the product lanes correct for compliance. ProKure V is the EPA-registered liquid disinfectant (EPA Reg. No. 87508-3-89334) for hard, non-porous surfaces at 10 minutes at 100 ppm, and it is suitable for use with plants in the room, treating surfaces, not plants, crop, or feed. ProKure G is the fast-release gas for an empty room and its label states it is not for use with or on plants, crops, or feed. ProKure D is the slow-release gas that improves air quality and controls odors for up to 30 days and runs with plants in the room, and it is not an EPA-registered pesticide. Match the tool to the step, and never borrow one product's disclaimer for another.

The documentation trail an auditor accepts

The response is only as good as its paper. A defensible log carries the sample IDs, the chain of custody, the remediation method used, the sanitizer's SDS and EPA label reference, the retest COA, and the final batch disposition. For a multi-state operator, standardize to the strictest limit you operate under so one SOP covers every state, then keep the per-state threshold appendix current. That trail is what turns a sanitation event into evidence a regulator will accept rather than a story you tell after the fact.

USP microbial limits and when to call for help

For the USP question: cannabis TYMC frameworks commonly borrow from USP general chapters, with USP <62> covering tests for specified microorganisms and the total-count methods informing yeast-and-mold and aerobic limits; advisory bodies have recommended mold counts not exceed 10,000 CFU/g. If your counts are trending up across cycles, or you operate across states with different limits, the protocol design and the audit trail are worth building with help rather than improvising mid-fail. GroClarity builds the CFU-banded SOP and the documentation around it.

Related resources