Botrytis Prevention Protocol for Cannabis Flower: A Week-by-Week SOP for Plants-in-the-Room Air Quality

Bud rot ruins otherwise clean crops because it waits for one bad night. Botrytis cinerea, the gray mold behind bud rot, turns a dense cola into a brown, water-soaked collapse fast, and the damage shows up where you cannot see it, inside the bud. The protocol below is preventive, not curative: it closes the humidity, canopy, and airflow windows the fungus needs, week by week through flower, and adds a plants-in-the-room air-quality layer so the room itself is working against spores. If you are new to running a dated SOP, this is the version to start from.

Why bud rot still beats clean rooms

Botrytis cinerea does not need a dirty room. It needs moisture, a dense canopy, and time. Extension guidance from the Pacific Northwest handbooks is blunt that canopy management is the single best preventive method, because still, humid air trapped inside a thick canopy is the whole game. The compliance stakes raise it from a yield problem to a business one: a positive pre-sale yeast and mold panel can hold or destroy a six-figure harvest and put a license at risk, which is why a head grower treats prevention as the job, not the afterthought.

The environmental window that lets Botrytis win

Three conditions open the door. Humidity is first: published greenhouse research on cannabis inflorescences shows Botrytis destroys buds rapidly under high relative humidity, so late flower has to run dry. Temperature in the roughly 50 to 80 degree Fahrenheit range favors infection. And free water is the accelerant: when buds stay wet for 12 hours or more, you have handed the fungus an infection window. Add a dense, poorly ventilated canopy and all three stack. The protocol attacks each one.

The week-by-week prevention SOP

Weeks 1 to 3, stretch: hold relative humidity around 55 to 60 percent and VPD near 1.0 to 1.2 kPa. Finish topping, lollipop the lower third, and lollipop again as the canopy fills, so air can move through it.

Weeks 4 to 6, bulk: step RH down to 50 to 55 percent and VPD to 1.2 to 1.4 kPa. Run a defoliation pass to open the interior, hang the slow-release ClO2 air-quality layer, and start a regular scouting cadence.

Weeks 7 to 9, ripen: drop RH to 45 to 50 percent and VPD to 1.4 to 1.6 kPa. No overhead water. Replace each ClO2 pouch before its up-to-30-day protection window closes so air-quality coverage stays continuous, and step scouting up to daily cola checks.

Final 7 to 10 days, finish: target about 45 percent RH, keep air moving, and resist the urge to spray anything on the buds. Document your harvest window. Between crops, reset the empty room before the next cycle inherits this one's spore load; that is a separate protocol with its own products.

The plants-in-the-room air-quality layer

This is the part most bud-rot guides skip, because most sanitation products cannot run around live flower. ProKure D is a slow-release ClO2 gas, a Gas Formula Packet that, in the label's approved language, provides ClO2 protection for up to 30 days and improves air quality and controls odors. It runs in an occupied room, which is exactly what a flowering crop needs. Deploy it as trifolds hung 18 to 24 inches above the canopy, and replace each pouch before its up-to-30-day window closes to keep ClO2 levels steady. Size to the room: a 95-gram pouch covers roughly 8,000 cubic feet, a 50-gram pouch roughly 4,000, and a 10-gram pouch roughly 1,000. There is no official two-week or 50/50 rotation schedule, so do not invent one; replace on the up-to-30-day window.

Keep the claim honest. ProKure D is not an EPA-registered product and is not labeled for sale as a pesticide under 40 CFR. It is an air-quality layer, not a fungicide you apply to the plant.

Scouting and early detection

Look where the air is stillest first: interior colas, bud sites pressed against leaves, the lower third of the canopy, and spots near drip lines. Early Botrytis shows as brown, water-soaked spots on buds or chlorotic areas on stems, progressing to a gray-brown mass of spores. Scout weekly through bulk and daily through ripen, because by late flower a day is the difference between losing one cola and losing a row.

What to do if you find an infected cola

Isolate before you cut. Bag the infected cola in place so you do not shake spores across the room, then make clean cuts well below the visible infection and dispose of the material off-site, not in the trim bin. Review your RH log and audit airflow to find the condition that let it happen, and fix that. Do not fog a surface disinfectant onto live buds, and do not apply a non-registered air product as a plant treatment. The response to an infection is isolation and environmental correction, not spraying the crop.

EPA posture and empty-room reset

For the live-flower air layer, ProKure D carries the disclaimer: Not an EPA-registered product and not labeled for sale as a pesticide under 40 CFR. Short-form, see product label for specific instructions and/or claims; long-form, it is a violation of Federal Law to use this product in a manner inconsistent with the labeling, so read the entire label and use strictly in accordance with precautionary statements and use. The empty-room reset between crops uses different products: ProKure V (EPA Reg. No. 87508-3-89334) for hard-surface disinfection at 10 minutes and 100 ppm, with Botrytis Sp. and Penicillium digitatum (ATCC 201167) on its fungicide list, and ProKure G (EPA Reg. No. 87508-2-89334) for a fast air reset in four to six hours. ProKure G carries the disclaimer Not for use with/on plants/crops/feed. Those are empty-room steps only.

Related resources