Botrytis cinerea is the crop-killer that turns a six-figure flower room into a loss in days. The lever that matters most is humidity. Peer-reviewed cultivation research shows Botrytis destroys cannabis inflorescences rapidly above roughly 70 percent relative humidity, and one widely cited grower guide notes that holding RH below 50 percent during flowering significantly reduces gray-mold risk. So the protocol is a declining RH curve across flower, matched airflow, disciplined pruning, and a residue-free sanitation cadence. None of the chemistry goes on the plant. This page gives the week-by-week targets, the airflow numbers, the scouting response, and the EPA lanes.
Why Botrytis is the six-figure risk in flower
Botrytis eats buds from the inside out, often invisibly until the lesion breaks the surface, and a single outbreak can sweep a dense late-flower canopy. The activation condition is environmental: peer-reviewed work ties rapid inflorescence loss to relative humidity above 70 percent. There is also a compliance angle. A Botrytis bloom drives your Total Yeast and Mold Count up, and a rising count fails a state pre-sale test on a crop you have already spent a full cycle growing. Prevention here is not hygiene theater; it is protecting the batch value.
The environmental targets by flower week
Run RH on a declining curve as the canopy fills and buds densify. Weeks 1 to 2, canopy establishment: about 55 to 60 percent RH. Weeks 3 to 5, mid-flower: about 50 to 55 percent. Weeks 6 to 8, late flower: about 45 to 50 percent. The last 10 days, finishing: about 40 to 45 percent. The single hard line from the research is to stay well clear of the 70-percent-plus window where Botrytis accelerates. Treat these curves as cultivation IPM consensus targets, not fixed law, and tune to your genetics and room.
The airflow protocol
Still, humid air inside a dense canopy is where Botrytis starts. Aim for gentle, continuous intra-canopy air movement, on the order of 0.3 to 1.0 meters per second, so no pocket sits stagnant. Use oscillating fans placed to move air through, not just over, the canopy, and size dehumidification so the room holds its RH target through lights-out, when temperature drops and relative humidity spikes toward condensation. Published guidance also stresses plant and row spacing to promote air movement around the plants.
The sanitation cadence and what ClO2 actually does
Chlorine dioxide (ClO2) is a selective oxidizer, and the ProKure line splits into clear roles. ProKure V is the EPA-registered liquid disinfectant (EPA Reg. No. 87508-3-89334) for hard, non-porous surfaces at 10 minutes at 100 ppm; its organism list includes Botrytis sp., and it is suitable for use with plants in the room because it treats surfaces, not the plants. ProKure D is the slow-release gas that improves air quality and controls odors and provides ClO2 protection for up to 30 days, running with plants in the room. ProKure G is the empty-room fast-release gas and is not for use with or on plants, crops, or feed. Use V to sanitize surfaces between cycles and in the trim room, and D to manage flower-room air on a monthly cadence. The chemistry is not sprayed on the bud.
Cultural practices that stack with the chemistry
Environmental control does the heavy lifting, and cultural practices close the gaps. Defoliate and prune the lower canopy on a schedule so dense, shaded, humid pockets do not form. Space plants and orient rows to promote air movement, as the extension guidance advises. Time irrigation so foliage and media are not holding free moisture into lights-out. Scout daily for the first gray-brown lesions at the densest cola centers, because early detection decides whether you lose a plant or a room.
The response when you find a lesion
Move fast and clean. Isolate the affected plant, cut well past the visible lesion into clearly healthy tissue, and bag the infected material on the spot so you do not shed spores across the canopy. If the rot is extensive or deep in multiple colas, pull the plant entirely rather than nursing it. Afterward, sanitize the surfaces and tools the plant touched with ProKure V at label strength and verify your RH and airflow targets are actually holding, because a lesion means the environment already drifted.
EPA lanes, documentation, and getting help
Keep the product lanes correct: ProKure V (EPA Reg. 87508-3-89334) for surfaces and suitable with plants in the room, ProKure G for empty-room gas and not for use on plants, crops, or feed, and ProKure D for air quality and not an EPA-registered pesticide. Because ClO2 gas dissipates rather than leaving residue, it fits a flower-room program without the residue concerns that on-plant chemistries raise. Log your RH and VPD readings, sanitation events, SDS and label references, and scouting notes for the auditor trail. If Botrytis recurs each cycle, the environment is still drifting somewhere, and a facility-specific protocol is worth building with help. GroClarity builds the flower-stage Botrytis SOP and the data trail around it.
Related resources


