The results for this query are the LCB education page, retail explainers, and pesticide-testing news. None publishes the working numbers a cultivator needs, so this page names the regulator, the rule sections, the test lines, and the fail response, and tells you where a figure has to be confirmed against the current WAC rather than guessed.
Who regulates cannabis mold testing in Washington
The LCB regulates it and certifies the independent third-party laboratories that run it. The lab-certification requirement sits in WAC 314-55-102, and the LCB's own education material is blunt about the gate: "Before a licensed retailer can sell a cannabis product to a consumer, the product must be tested by a certified cannabis laboratory to make sure it is safe to consume." Washington is one of the oldest legal markets (I-502 passed in 2012), so its mold ruleset is mature and mycotoxin-forward, with water activity used as a moisture gate on top of the microbial and mycotoxin screens.
The three test lines that gate mold
Mold shows up across three screens, and understanding which is which keeps an operator from chasing the wrong number.
- Water activity: a moisture gate. The LCB states water activity "ensures the product's moisture level is not susceptible to mold." The WAC sets an upper water-activity limit (commonly cited at 0.65 aw in operator training); confirm the current figure against WAC 314-55 before you build it into an SOP.
- Microbiological screening: the LCB describes it as ensuring the product does not carry bacteria "such as E. Coli or Salmonella above the action limits," alongside the mold and yeast load.
- Mycotoxin screening: the LCB describes it as ensuring the product does not carry "harmful molds or fungi above the action limits," which covers the mycotoxin byproducts (aflatoxins and ochratoxin A) that certain molds produce.
The LCB defines an action limit as "the percentage of a substance at which it may pose a health hazard, and therefore action must be taken to eliminate the health risk." The LCB education page does not publish the numeric action limits, so for the exact total yeast and mold, Aspergillus, aflatoxin, and ochratoxin A figures, read them off the current WAC and your lab's COA format rather than a third-party chart. Where a number cannot be confirmed from the rule, write "confirm with the LCB" into the SOP instead of copying a figure.
What happens on a fail
A batch that exceeds an action limit cannot be sold as-is. Depending on the product category, Washington's rules allow some categories to be remediated (for example into an extract) while others must be destroyed, and retesting is governed by the WAC. The remediation-versus-destruction call and the retest pathway are exactly what a head grower staring at a six-figure batch needs, and they are set in WAC 314-55-102; confirm the current retest window and the categories eligible for remediation with the LCB, because those details change by rule revision.
Prevention is the part the rules do not cover
Every ranking page stops at test, pass, or fail. None addresses the upstream work that keeps a batch under the action limit in the first place: environmental control, airborne spore load, and residue-free between-cycle surface sanitation. That is the gap GroClarity fills, and it is where the ProKure ClO2 line fits, matched product to job. ProKure V is a liquid Hospital-Type Disinfectant, EPA Reg. No. 87508-3-89334, applied to hard, non-porous surfaces at 100 ppm for a 10-minute exposure, suitable for use with plants in the room and residue-free, with a hard-surface kill list that includes Aspergillus niger (ATCC 9642), Fusarium solani (ATCC 36031), and Botrytis sp. ProKure G is a fast-release gas Deodorizing Delivery System, EPA Reg. No. 87508-2-89334, for an empty-room reset in 4 to 6 hours, carrying the label instruction Not for use with/on plants/crops/feed. ProKure D is a slow-release gas that provides ClO2 protection for up to 30 days of air quality and odor control; it is not an EPA-registered product and not labeled for sale as a pesticide under 40 CFR, and it runs with plants in the room. Surface work is V, empty-room reset is G, ongoing air quality is D. Full labels and SDS live on prokuresolutions.com.
How Washington compares to other states
Washington's thresholds do not transfer across state lines, and that is the whole problem for a multi-state operator. Its mycotoxin-first, water-activity-gated ruleset predates most adult-use markets and reads differently from a newer medical-only state or a tiered adult-use state. Confirm each state's action limits with that state's regulator rather than assuming Washington's numbers travel, and keep a per-state SOP under one standardized prevention practice.
Talk to GroClarity
GroClarity is headquartered at 5013 E. Washington St. Ste. 130, Phoenix, AZ 85034, and works with cultivators on an EPA-compliant prevention protocol built around the state testing panel, with an audit-ready data trail. For a Washington-specific compliance engagement, request a quote through the cultivation IPM expertise program; to order product, reorder on shop.groclarity.com. The mold prevention protocols coverage carries the room-level practice and the air quality management coverage carries the monitoring side.
Frequently asked questions
Who regulates cannabis mold testing in Washington?
The Washington State Liquor and Cannabis Board (LCB) regulates it and certifies the labs that run it, under WAC 314-55. The lab-certification requirement is in WAC 314-55-102. Confirm the current numeric action limits and water-activity figure against the WAC and your lab's COA rather than a third-party reference table, because the LCB education page does not publish the numbers.
What does Washington test cannabis for related to mold?
Three screens gate mold: water activity (a moisture limit the LCB says keeps the product from being susceptible to mold), microbiological screening (mold, yeast, and bacteria above the action limits), and mycotoxin screening (the aflatoxin and ochratoxin A byproducts of certain molds). An action limit, per the LCB, is the level at which a substance may pose a health hazard and action must be taken.
What is the water activity limit for cannabis in Washington?
The WAC sets a water-activity upper limit used as a mold-moisture gate, commonly cited at 0.65 aw in operator training. Because the exact current figure is set in rule and not published on the LCB education page, confirm it against WAC 314-55 before building it into an SOP. Water activity is a moisture gate, not a direct mold count.
What happens if a batch fails mold testing in Washington?
A failing batch cannot be sold as-is. Washington's rules allow some product categories to be remediated (for example into an extract) while others must be destroyed, with retesting governed by WAC 314-55-102. Confirm the current retest window and which categories are eligible for remediation with the LCB, and treat prevention as the durable fix rather than retesting toward a pass.
Can ProKure be used to prevent mold with plants in the room?
Match the product to the label. ProKure V (EPA Reg. No. 87508-3-89334) is a surface disinfectant suitable for use with plants in the room and leaves no residue. ProKure D runs with plants for ongoing air quality and is not an EPA-registered product and not labeled for sale as a pesticide under 40 CFR. ProKure G is an empty-room gas labeled Not for use with/on plants/crops/feed. Read the product label for each.


