Who this applies to in Virginia
Virginia's cannabis testing rules sit under the Virginia Cannabis Control Authority (VCCA), Agency 10, Chapter 60. The medical program is live; adult-use retail rulemaking has been delayed across multiple sessions and is not yet operational.
Pharmaceutical processors and cultivation facilities
The rule reaches two operators. Per 3VAC10-60-20(C): "A pharmaceutical processor or cannabis cultivation facility shall make a sample available from each harvest batch of botanical cannabis product." If you harvest flower in Virginia, this is your rule. Oil batches fall under Section B, which requires a minimum sample size of 0.5% of individual units from each homogenized batch.
What pending adult-use rulemaking is likely to add
Virginia legalized adult-use possession in 2021, but retail rules are still pending. Cultivators preparing for the expanded market should treat 3VAC10 as the likely template. Total yeast and mold (TYM) readiness now is a day-one licensing advantage when the expanded rules land.
The exact regulation: 3VAC10-60-20 broken down
The whole mold-testing obligation lives in a handful of subsections. Here is what each one does.
Section C: the required test panel per harvest batch
Every harvest batch of botanical cannabis is tested for microbiological contaminants, mycotoxins, heavy metals, pesticide chemical residue, water activity, and moisture content, plus active ingredient and terpene analysis. The sample "must be representative of the entire batch to include selection from various points in the batch lot."
Section H: botanical cannabis pass/fail standards
Section H is the pass/fail gate: a sample "shall pass the microbiological, mycotoxin, heavy metal, water activity, or moisture content test based on the" applicable standard. For microbiological pass/fail, Virginia points to the American Herbal Pharmacopoeia Cannabis Inflorescence monograph rather than publishing its own CFU/g number.
Sections D and E: segregate, and do not sell before the COA
Section D requires the processor to "segregate and withhold from use the entire batch" from the time of sampling until results return. Nothing moves to sale before the COA. That hold time, typically three to seven business days for a full panel, is a real cost on your sell-through calendar, not a formality.
Translating the AHP Cannabis Inflorescence standard into a real TYM number
The single biggest gap on every page ranking for this query: the regulation offloads the microbiological threshold to the AHP monograph, and no one explains what AHP actually says.
Why Virginia offloads the number to AHP
3VAC10-60-20(H) does not print a CFU/g limit. It incorporates the AHP Cannabis Inflorescence microbiological standard by reference. That means a grower reading the regulation alone cannot compute a pass probability. You have to go to the monograph.
What operators typically use in their SOP
The widely cited AHP inflorescence limit for total yeast and mold is 10,000 CFU/g (10^4 CFU/g), paired with pathogen-specific testing for the Aspergillus species A. flavus, A. fumigatus, A. niger, and A. terreus in many operator SOPs. Confirm the current monograph edition and your lab's method before you build this into a facility SOP, because the reference, not a VCCA number, is what your lab reports against.
How Virginia compares to Maryland, Florida, and Oklahoma
This is where Virginia differs from its neighbors. Maryland publishes explicit numeric CFU/g thresholds directly in its rules; Oklahoma's OMMA sets numeric limits; Virginia defers to AHP. If you operate across state lines, you cannot assume one number travels. See the Maryland cannabis mold testing requirements for the numeric-threshold version of this page.
Mycotoxin, water activity, and moisture: the mold prevention math
Three of the five tests are the levers a cultivator actually controls upstream in cure.
Mycotoxin: 20 ppb total
The mycotoxin cap is a total of 20 ppb, driven mostly by aflatoxins and ochratoxin A, which are metabolites of the same Aspergillus and Penicillium molds the microbiological test screens for. Control the mold load in the room and the cure, and you control the mycotoxin risk at the same time.
Water activity 0.65 Aw is the mold suppression gate
Water activity at or under 0.65 Aw suppresses most xerophilic mold growth, which is why the limit exists. Treat hitting 0.65 Aw in cure as a strategic decision, not a QA afterthought. The cure environment, temperature, humidity, and airflow, is what drives the final Aw reading and, with it, your microbiological pass probability.
Moisture at or under 15%
The moisture content limit is 15%. Moisture and Aw move together: a tight, well-managed cure brings both into spec and starves mold of the free water it needs to reproduce before the batch ever reaches the lab.
What causes a mold failure, and the sanitation that prevents it
A batch fails the microbiological test because the room reseeded the crop with spores, not because the lab was unlucky. The prevention happens between cycles, before the plants go back in.
Where the spore load hides
Airborne spore load between cycles, residual biofilm on rolling benches, walls, and HVAC returns, and a contaminated cure room are the three usual sources. A room that looks clean can still carry viable inocula on porous surfaces and in ductwork the mop never reaches. The between-cycle turnover is the intervention that determines whether the end-of-cycle QA gate passes or fails.
The ProKure ClO2 products that lower fail risk
The product-claim language here is used exactly as the labels state it. ProKure V is the liquid ClO2 surface disinfectant, EPA Reg. 87508-3-89334, used at 100 ppm for a 10-minute contact time on hard, non-porous surfaces, residue-free, and suitable for use with plants in the room because it is applied to surfaces and not the crop. ProKure V carries the ProKure disclaimer "Not for use on plants, crops, or feed." ProKure G is the fast-release ClO2 gas, EPA Reg. 87508-2-89334, for the empty-room turnover reset, carrying the verbatim restriction "Not for use with/on plants/crops/feed," working in four to six hours. ProKure D is the slow-release ClO2 gas that improves air quality and controls odors and provides ClO2 protection for up to 30 days, running with plants in the room; it is not an EPA-registered product and is not labeled for sale as a pesticide under 40 CFR, so it is logged as an air-quality measure, not a disinfection step. To order, go to shop.groclarity.com; for SDS and EPA labels, see prokuresolutions.com.
What to do when a batch fails, and how sampling works
A failed microbiological test is not automatically a total loss in Virginia.
Remediation is allowed with further processing
Regulation 3VAC10-60-20(G) states "The batch may be remediated with further processing." In practice, that can mean gas-phase treatment of the affected lot, extraction of failed flower into oil (which then retests under the Section B oil panel), or disposal when neither is viable. For a flowering crop worth six figures, the remediation path is a revenue-recovery decision, not a footnote. Document every step for your board reporting.
Sampling: what the lab controls and what you control
The lab determines the valid sample size and "may determine the minimum sample size for testing from each batch," and must take a representative sample from various points in the lot. You control batch heterogeneity: a single hot spot in one tote can swing a pass or fail depending on selection. The cleaner and more uniform the batch going in, the less your result rides on where the lab happened to sample.
EPA and FIFRA context every Virginia operator should understand
This is the compliance line no one on the Virginia SERP draws, and it is the one an auditor cares about.
FIFRA registration for any facility disinfectant
Under the Federal Insecticide, Fungicide, and Rodenticide Act (FIFRA), any product marketed with antimicrobial surface claims in a food-adjacent facility must carry an EPA registration number, regardless of state cannabis rules. That is why ProKure V states its EPA registration (87508-3-89334) for hard, non-porous surfaces, and why the "Not for use on plants, crops, or feed" disclaimer appears wherever application language does. Bleach and quat residue is an operational cost, not just a chemistry note: residue means a rinse step, crew downtime, and phytotoxicity risk to the next crop. A residue-free, labeled disinfectant removes that cost.
Next steps
If you run flower in Virginia, your pass rate is set in the room between cycles, not in the lab. Build the turnover sanitation into your SOP, confirm your lab reports against the current AHP monograph, and keep every SDS and EPA label on file for audit. For state-specific compliance consulting, request a quote. To spec ProKure V, G, or D into your program, order on shop.groclarity.com, or call GroClarity at 866.206.1301. Built on Science. Backed by Results.


