The governing statute is MCA 16-12-209, run by the CCD under the Department of Revenue. A cultivator, manufacturer, or dispensary may not sell marijuana or marijuana products until a testing laboratory has tested the batch and it meets the requirements of the section, and the licensee pays for the testing. You submit material collected under a department sampling protocol that divides product into batch sizes.

Two checks run in parallel. The lab conducts a visual inspection of each batch for foreign matter, debris, insects, and visible mold, and it runs the assay for contaminants the department names by rule. Visible mold is the naked-eye screen; the assay is what catches what you cannot see. The lab issues a certificate of analysis and reports results to the seed-to-sale tracking system. The statute was enacted by I.M. No. 190 in 2020 and amended by Ch. 576 in 2021 and Ch. 712 in 2023.

The actual standard: what the department requires by rule

The statute delegates the numbers. MCA 16-12-209 states the department shall establish by rule the acceptable levels of moisture, pesticides, residual solvents, mold, mildew, foreign matter, debris, insects, and other contaminants, so the pass or fail thresholds live in the department rules, not the statute.

For the mold family, Montana's adopted standard is species-level: Aspergillus (A. flavus, A. fumigatus, A. niger, and A. terreus) non-detectable in 1.0 gram, alongside Salmonella spp. and Shiga-toxin producing E. coli (STEC), both non-detectable in 1.0 gram. Montana does not publish a numeric Total Yeast and Mold Count action level the way many states do. A batch can carry a yeast-and-mold count that would fail in a count-based state and still clear Montana, and a batch with a low count still fails if any of the four Aspergillus species is detected. The Aspergillus speciation result is the hard gate.

The Montana testing workflow, step by step

Sampling follows the department protocol that defines batch size and sample collection, with a documented chain of custody. The lab runs the visual inspection and the contaminant assay, issues the certificate of analysis, and reports to the seed-to-sale system. On a fail, the statute gives two distinct paths. Under subsection (7), a licensee may request that failed material be retested under the department's retesting parameters. Under subsection (9)(a), the department collects and destroys samples that fail to meet acceptable levels. Product that passes must carry a label indicating it has been tested. Retest is a right you can exercise; destruction is the default for material that stays out of bounds.

Licensed Montana testing laboratories

Montana requires testing labs to hold ISO 17025 accreditation, a requirement reported as effective January 1, 2022. That accreditation is why a Montana cannabis result carries weight, and it is why the lab that tests your flower operates to a documented method standard rather than an in-house one. Confirm the current licensed-lab roster with the CCD before you contract, because the list changes.

What changed in 2023 and why operators pushed back

The 2023 amendments (Ch. 712, L. 2023) to MCA 16-12-209 tightened the testing framework. Reporting from the Daily Montanan documented that small-to-mid operators felt the post-2023 changes hardest, which maps to the single-room and small multi-room facility manager. If you run a smaller Montana operation, the practical takeaway is that the margin for a careless turnover shrank, and prevention moved from nice-to-have to budget line.

Preventing a failed mold test

The Aspergillus result is set by air, surfaces, staff movement, and inputs long before harvest. The prevention question for a flowering room is which chemistry you can use without evacuating the crop or leaving a residue.

Between cycles, disinfect every hard, non-porous surface with ProKure V, a liquid chlorine dioxide disinfectant, EPA Reg. No. 87508-3-89334, used at 100 ppm for a 10-minute contact time. Its label lists kill claims on hard surfaces against fungi including Aspergillus niger (ATCC 9642) and Fusarium solani (ATCC 36031). ProKure V is stated as suitable for use with plants in the room because it treats surfaces, not the crop, and it leaves no residue and needs no rinse on treated surfaces. That plants-in-room registration is the wedge: bleach and quaternary ammonium products cannot match a residue-free, plant-adjacent surface disinfectant.

For an empty-room reset between crops, ProKure G, a fast-release chlorine dioxide gas, EPA Reg. No. 87508-2-89334, works in 4 to 6 hours and then needs a 1-hour ventilation before re-entry. ProKure G carries the label disclaimer that it is not for use with plants, crops, or feed, so the room must be empty of plants and people. For ongoing air quality with plants present, ProKure D, a slow-release chlorine dioxide gas, provides ClO2 protection for up to 30 days; it is not an EPA-registered product and not labeled for sale as a pesticide under 40 CFR, and it carries no kill claims.

EPA compliance for prevention products used in Montana grows

Keep the three label positions straight, because conflating them is the error an auditor catches. ProKure V (EPA 87508-3-89334) is the surface disinfectant, suitable for use with plants in the room on hard, non-porous surfaces. ProKure G (EPA 87508-2-89334) is the empty-room gas, not for use with plants, crops, or feed. ProKure D runs in-room with plants present for air quality and is not EPA-registered. Close the loop with an audit trail: air-quality logs, sanitation records with the product, EPA registration number, contact time, and operator, so you can prove surface and air quality to a CCD auditor.