Under the Cannabis Legalization Act, a licensee may not sell adult-use cannabis to a consumer unless it has passed mandatory testing. The CLA names six analyte categories: residual solvents, poisons and toxins; harmful chemicals (metals); dangerous yeasts, molds and mildew (including mycotoxins); harmful microbes including E. coli and salmonella; pesticides, fungicides and insecticides; and THC potency, homogeneity and cannabinoid profiles. Results move fast: the testing facility must report to the licensee and to OCP within two business days through a Certificate of Analysis and electronic data deliverables. The governing numbers live in 18-691 C.M.R., ch. 5, Section 6, and that rule is where you confirm the current pass/fail threshold for your matrix.
The yeast and mold thresholds, and where to confirm them
Maine defines a fail as a sample containing a contaminant above the failure threshold for that analyte as prescribed in 18-691 C.M.R., ch. 5, Section 6. The threshold is set by rule and applies per matrix (usable cannabis, concentrates, infused products), so the Total Yeast and Mold limit that governs your flower is not necessarily the one that governs an extract. Confirm the current CFU-per-gram figure for your matrix directly against 18-691 C.M.R., ch. 5, Section 6 rather than carrying over a neighboring state's number, because the rule is the controlling source and it changes by matrix. Mycotoxins are tracked as their own analyte; in Q2 2026, 0 of 19 mycotoxin samples failed across all matrices.
Q2 2026 fail-rate data: what the numbers actually say
The OCP Q2 2026 Adult Use Sample Report is specific. Total Yeast and Mold on usable cannabis: 163 fails of 2,396 samples, a 6.80 percent fail rate. On concentrates: 0 of 1,163, or 0.00 percent. On infused products: 0 of 373, also 0.00 percent. Across all matrices, yeast and mold ran 163 of 3,932, a 4.15 percent fail rate. The program-wide number across every analyte was 207 fails of 4,490 samples, 4.61 percent (source: maine.gov OCP Q2 2026 report). The story those numbers tell is blunt: the yeast and mold risk is concentrated almost entirely in raw flower, because extraction and infusion processes knock the microbial load down. If you sell usable cannabis, this is your number.
What happens when a batch fails
A fail in Maine is public and it moves product off shelves. The Office of Cannabis Policy issued its first adult-use recall in September 2024 for Cannabis Cured flower and pre-rolls that failed a yeast and mold test, pulled from eight retail stores and sold between August 27 and September 9, 2024. Green Trap flower and a Nova Farms recall followed on the same contaminant. In May 2026, OCP issued a medical-cannabis advisory after a sample tested at 18 times the recreational limit. The health language OCP uses in recall notices is plain: smoking cannabis with unsafe mold levels can lead to "sinus issues, allergies, headaches, dizziness, or fatigue." A recall is the expensive version of a problem that a prevention program is built to avoid.
Remediation is permitted for yeast and mold
Here is the part that separates yeast and mold from metals and pesticides. Per OCP, for metals and pesticides remediation is not permitted, though a licensee may submit two samples for retesting after an initial fail. For yeast, mold, microbials, and residual solvents, remediation is permitted. In practice that means a failed yeast and mold batch can be quarantined, remediated, and resubmitted for mandatory retesting rather than destroyed outright. Keep the chain of custody and the documentation tight through that loop, because the retest COA and the electronic data deliverable both land with OCP, and a clean paper trail is what turns a fail into a recovered batch instead of a write-off.
Prevention: closing the gap between harvests
A 6.80 percent flower fail rate is a prevention problem before it is a testing problem. Yeast and mold enter during the grow and concentrate during the between-cycle window, when a room is turned over under time pressure. The common sanitation default, bleach, leaves residue and fumes that force crew evacuation and 3 to 5 days of downtime. The ProKure line maps to the three jobs of a turnover. ProKure V is the EPA-registered liquid Hospital-Type Disinfectant (EPA Reg. No. 87508-3-89334) for hard, non-porous surfaces such as grow beds, benches, and tools, and it leaves no residue and is suitable for use with plants in the room. ProKure G is the fast-release gas for an empty-room air reset between harvests, working in 4 to 6 hours, and its label carries the restriction "not for use with/on plants/crops/feed," so it runs only when the room is stripped. ProKure D is a humidity-activated slow-release gas that improves air quality and controls odor and provides ClO2 protection for up to 30 days per pouch, running with plants in the room; D is not an EPA-registered product and not labeled for sale as a pesticide under 40 CFR. Keep each claim on its own product and its own label.
Cost, records, and working with GroClarity
Testing is a line item you can price. MCR Labs lists microbiological contaminant testing in Maine at $140 per sample on 1.3 grams of flower, a reference point for budgeting your mandatory-testing cadence. For records, keep the COA, the electronic data deliverable confirmation, your between-cycle sanitation SOP, and the SDS and EPA label for any product you use (available from prokuresolutions.com) in one audit file. GroClarity, based in Phoenix, Arizona at 5013 E. Washington St. Ste. 130, Phoenix, AZ 85034, works with cannabis cultivation facilities nationwide by appointment to build the air-quality baseline and the between-cycle protocol that keep a Maine facility out of that 6.80 percent. Product orders route to shop.groclarity.com. Always read product labels before use.


