The ProKure V versus ProKure G decision is not really a choice between two SKUs in a catalog, which is how every page ranking for this query frames it. It is a choice between two treatment modalities: liquid surface contact versus airborne gas. Get that framing right and the decision answers itself. If the problem is a surface you can reach, bench, tray, tool, wall, drain, you spray or wipe ProKure V. If the problem is a whole room, including the ductwork, the HVAC return, the ceiling, and the porous material a liquid never touches, you fog ProKure G in the empty, sealed room. Both are chlorine dioxide (ClO2); they differ in how they are delivered and where they can go.

ProKure V and ProKure G at a glance

ProKure V is a liquid Hospital-Type disinfectant and fungicide for hard, non-porous surfaces, EPA Reg. No. 87508-3-89334. It is water-activated from a pouch, used at a working concentration of 100 ppm with a 10-minute contact time to disinfect, requires no rinse, and leaves no residue. A 0.84 oz pouch makes 5 gallons of solution at 100 ppm; a 0.17 oz pouch makes 1 gallon. Crew apply it with standard PPE while the room stays occupied, because it is suitable for use with plants in the room, applied to the surface and not to the plant.

ProKure G is a fast-release chlorine dioxide gas, EPA Reg. No. 87508-2-89334, that works in 4 to 6 hours. It is the solution to mold and mildew, odor-causing bacteria, and chemical odors, delivered as deep-penetrating ClO2 vapor that reaches throughout the airspace. A 10-gram packet covers approximately 1,000 cubic feet; a 25-gram packet covers approximately 2,250 cubic feet. ProKure G carries the verbatim label restriction Not for use with/on plants/crops/feed, so it runs only in an empty, sealed, unoccupied room: people and plants out, treat for 4 to 6 hours, then ventilate for one hour before re-entry.

What the ranking pages leave out

The SERP for this query is a catalog, not a comparison. The manufacturer page ranking first is a tradeshow lead-capture page whose only product line is the marketing hook that ProKure "helped cultivation facilities across the U.S. solve mold issues with ProKure V and ProKure G and improve air quality with ProKure D." That sentence names all three products and explains none of the choice. The retailer collections do the same at the SKU level, listing a "Prokure V - 0.84 oz. Chlorine Dioxide Liquid Mold and Mildew Eliminator, 5 Gallon @ 100 ppm" next to a "Prokure G - 10 Gram Chlorine Dioxide Fast Release Gas, 1000 cu. Ft." with no guidance on which one a grower should reach for. Nobody puts the two numbers that actually drive the decision, the 100 ppm 10-minute contact time for V and the 4-to-6-hour room fog for G, side by side. That is the gap this page fills.

Choosing by scenario

The decision usually comes down to which of two situations you are in. You just got a positive mold or yeast-and-mold result on a mature crop and need a response: that is usually a whole-room reset once the room is clear, which is ProKure G territory, with ProKure V for the specific surfaces that staged the affected material. You are turning a room between cycles and want it done fast without a bleach evacuation: run ProKure G as the empty-room airspace reset and ProKure V on the benches, trays, and tools, and the turn happens without a rinse step or a residue on the next crop’s surfaces.

Often the answer is both, used for different jobs in the same turn. V handles the surfaces crew can reach; G handles the airspace and the ductwork crew cannot. They are not competitors so much as the surface half and the air half of a single room reset. The one rule that keeps them straight is occupancy: V can run with the crop in the room because it is applied to a surface; G runs only in an empty, sealed room because it fills the whole airspace with gas.

EPA labels and the plant-contact rule

For a regulated grow, the label line that matters most is the plant-contact rule, and it belongs to G, not V. ProKure G carries the verbatim restriction Not for use with/on plants/crops/feed, which is why it is an empty-room treatment. ProKure V carries no such restriction: it is a hard, non-porous surface disinfectant that is suitable for use with plants in the room, because you treat the surface and the plant is never the target. Keep that distinction exact at audit time: it is a violation of Federal Law to use either product in a manner inconsistent with its labeling, so match each SKU to its labeled use. For procurement, both products carry an EPA registration number and a Safety Data Sheet; pull the full labels and SDS from prokuresolutions.com for the audit binder.

Residue, crew safety, and re-entry

Both products beat bleach and quats on the two pains a facility manager feels most. Residue: ProKure V leaves no residue and requires no rinse on hard, non-porous surfaces, and ProKure G, being a gas, leaves no liquid residue at all, so neither leaves a film on the surfaces that stage finished flower. Crew disruption: ProKure V is applied by crew with standard PPE and no room evacuation, while ProKure G requires the room empty and sealed for the 4-to-6-hour treatment and a one-hour ventilation before re-entry. That occupancy difference is the operational variable to plan around: V fits into a working shift, G fits into a closed window such as an overnight turn.

Where V and G sit next to ProKure D

This page is the V-versus-G decision, and it deliberately does not sell the third product. For completeness: ProKure D is a slow-release gas that provides ClO2 protection for up to 30 days and improves air quality and controls odors with plants present. It is not an EPA-registered product and is not labeled for sale as a pesticide under 40 CFR, and it carries no kill claims, so it is an ongoing air-quality layer, not a treatment, and it is a different decision from the V-versus-G one. If your real question is ongoing air quality rather than a surface-versus-airspace treatment choice, that is thegrow-room air quality managementdecision, not this one.

Where to buy

Educate here, buy on the store. ProKure V comes in 0.17 oz (1 gallon) and 0.84 oz (5 gallon) pouches; ProKure G comes in 10-gram (1,000 cubic feet) and 25-gram (2,250 cubic feet) packets. Size V by the surface area and gallons of working solution you need, and size G by the cubic-foot volume of the room. Order the SKUs that map to your facility on shop.groclarity.com, and pull full technical spec, EPA registration numbers, and SDS from prokuresolutions.com.

Related resources

Related resources