ProKure V vs G vs D: Which ClO2 Product Fits Your Grow Room?

All three are chlorine dioxide (ClO2). What separates them is the form and the room state they are built for. ProKure V is a liquid surface disinfectant you use on hard non-porous surfaces with plants in the room. ProKure G is a fast-release gas for an empty, unoccupied room between cycles. ProKure D is an extended-release gas that holds air quality and controls odor for up to 30 days while the crop stays in place. If you remember one rule, remember the room-state fork: plants present and treating surfaces is V, empty room reset is G, plants present and treating the air is D.

That is the whole decision. The rest of this page is the detail behind it, plus the one compliance boundary you cannot cross.

The 30-second answer

V for hard-surface disinfection with plants present, applied to surfaces and never directly onto the plants. G for an empty room that needs a full-space reset, with no people, pets, or plants in the room during treatment. D for ongoing air quality and odor control while plants are in the room, for up to 30 days per pouch. One is a liquid, two are gases, and the gases split on whether the room is occupied.

Quick-reference comparison

The table below puts the three on the axes a grower actually decides on: form, job, EPA status, whether plants can be present, duration, and PPE.

DimensionProKure VProKure GProKure D------------FormLiquid (water-activated)Fast-release gasExtended-release gasPrimary jobDisinfect and deodorize hard surfacesReset and deodorize a whole empty spaceImprove air quality and control ongoing odorEPA statusEPA-registered hospital-type disinfectant (Reg. No. 87508-3-89334)EPA-registered (Reg. No. 87508-2-89334)Not an EPA-registered product and not labeled for sale as a pesticide under 40 CFRPlants in the room?Yes, suitable for use with plants in the roomNo, unoccupied spaces onlyYes, can be used while plants are in the roomOn the plants directly?No, hard non-porous surfaces onlyNot applicable (gas for an empty space)Not applicable (air treatment)DurationReapply per protocol; activated solution within 15 daysSingle treatment cycleUp to 30 days per pouchPPENone required at 100 ppm, gloves if hands contact activated solutionNot required because the space is unoccupied; ventilate one hour before re-entryPer labelApplicationSprayer, mop, or sponge; no foggingActivated pouch placed 18 to 24 inches from fabrics, leather, electronics, metalsHumidity-activated pouch, placed or hung

Two things in that table decide most purchases: the plants-in-the-room row and the EPA-status row. Read those two first. If plants are in the room and you are treating surfaces, you are in V territory. If the room is empty, G is on the table. If plants are in the room and you are treating the air for the long haul, that is D. Everything else in the table is detail that confirms the choice rather than driving it.

ProKure V: the liquid surface disinfectant

V is the liquid, a water-activated Hospital-Type Disinfectant, EPA Reg. No. 87508-3-89334. You reach for it when a room has plants in it and you need to disinfect the hard surfaces: benches, trays, tools, drip lines, drop-down hoses. Apply it at 100 ppm for a 10-minute exposure by sprayer, mop, or sponge. Do not fog it. It leaves no residue.

The plant-safety boundary is the part people get wrong, so be precise. ProKure V is suitable for use with plants in the room, but it is for hard non-porous surfaces, not for use directly on the plants. Those are two different statements, and the label means both. You can work around a live canopy; you are not spraying the canopy. That distinction is exactly why V, not G, is the surface tool you use while the crop is in place: G cannot be in an occupied room at all, while V is built to be.

On kill claims, V is the only one of the three that carries them, and that is a meaningful distinction when you are spec-ing a program. G controls odor-causing bacteria, mold, and mildew in an empty space, and D makes air-quality statements only; neither is the tool you cite when you need a documented surface kill. V kills SARS-CoV-2 on hard non-porous surfaces in 30 seconds, and the label organism list includes Aspergillus Niger (ATCC 9642), Fusarium Solani (ATCC 36031), Penicillium Digitatum (ATCC 201167), Botrytis Sp, and bacteria such as MRSA (ATCC 33591). V also holds an NSF International certificate in the D2 category, meaning it is considered a sanitizer on surfaces not always requiring a rinse. On PPE, at 100 ppm V does not require respiratory PPE; wear gloves if your hands will contact the activated solution during dilution or application. An activated batch, stored in a dark sealed container, is good for up to 15 days from activation. Once you have chosen V, the full ProKure V product detail, dilution tables, and SDS live on prokuresolutions.com.

ProKure G: the fast-release gas

G is the fast-release gas, EPA Reg. No. 87508-2-89334. You reach for it to reset an empty room between cycles, to deodorize a whole space fast, or for a ventilation-system treatment. It works in 4 to 6 hours.

G carries one rule you cannot bend, and it is the reason G and D are not interchangeable: G is for unoccupied spaces only. No people, no pets, and no plants in the room during treatment. Its label states not for use with/on plants/crops/feed. This is an empty-room tool, full stop.

The placement mechanics matter because ClO2 gas is heavier than air. Activate the pouch in a high, central location, no closer than 18 to 24 inches from fabrics, leather, electronics, mirrors, metals, or plated surfaces, and use a fan or air mover to distribute the gas through the space. The 18-to-24-inch clearance is not a suggestion; the gas is an oxidizer and close contact can mark sensitive materials, so plan the placement before you activate rather than after. People and pets stay out while the product is active; use the caution placards to mark treatment and safe re-entry times, and ventilate for one hour before anyone re-enters. PPE is not required precisely because the space is unoccupied, though chlorine dioxide gas can irritate the respiratory tract if the product is not used in strict accordance with the label. Once you have chosen G, the full ProKure G product detail and SDS live on prokuresolutions.com.

ProKure D: the extended-release gas

Start D with the compliance boundary, because it is the single most important sentence for a cultivator building an SOP. ProKure D Extended-Release is not a disinfectant or pesticide. It is not registered with the EPA and has no kill claims regarding disinfection or sanitization. The required disclaimer is verbatim: Not an EPA-registered product and not labeled for sale as a pesticide under 40 CFR. Put that line where your team and your auditor will see it, not buried at the bottom of a spec.

What D actually does is narrower and, for a live grow, exactly right: it improves air quality, provides ClO2 protection for up to 30 days, and controls ongoing nuisance odors. Keep the up-to qualifier; it is up to 30 days, not a flat 30. The up-to matters for both compliance and expectations: it is a maximum protection window, not a guaranteed flat duration, and writing it as a hard 30 overstates the label. D is humidity-activated, placed or hung on a surface, and sized to the room volume, so it runs quietly in the background through the grow rather than as a one-time event. Because D makes air-quality statements rather than kill claims, it can be used while plants are in the room, which is precisely what makes it the air half of a program that runs through flower, dry, and cure. For a cannabis facility, D is the tool that holds air quality steady between tests and keeps odor under control during flower without touching the crop. Once you have chosen D, the ProKure D overview and the verbatim disclaimer live on prokuresolutions.com, and the competitor-versus-D source-strength comparison lives on the GroClarity blog.

Decision framework by room state

Growers think in room states, not SKU names, so map the three that way.

Room full of plants with a positive mold or pathogen swab: disinfect the hard surfaces with V and keep D running for the air. You are not treating the plants; you are lowering the pressure around them.

Room empty between cycles: run a G full-space reset, then wipe surfaces with V before you re-populate. G handles the air and the whole envelope while the room is empty; V handles the surfaces the next crop will touch. The order matters: G first while the room is sealed and empty, then V on the surfaces once the room is vented and you can work in it. This is the sequence that turns a multi-day bleach-and-air-out turnover into a same-day reset, which is exactly the downtime a facility manager is trying to claw back.

Room in flower or dry and cure with strong odor: run D for ongoing air quality and odor, with the crop in place.

Ventilation-system decontamination: use G following the ductwork protocol on the ProKure G label.

Decision framework by operator

Head Grower running multi-room cultivation: you want all three on an SOP, V for surface turnover, G for the empty-room reset, D for in-cycle air quality, with an air-sample log behind each so you can prove the program to ownership and auditors.

Facility Manager doing between-cycle turnovers: your workhorses are G (the fast empty-room reset that shrinks downtime) and V (the no-rinse surface wipe before re-populating).

MSO Cultivation Director standardizing across states: the value is one ClO2 line and one SOP defended across every state footprint, rather than a patchwork of vendors room to room.

QA or Procurement building a program spec: you need the EPA status and documents straight, V and G registered with their reg numbers on file, D carrying its 40 CFR disclaimer, and an SDS for each in the audit binder. The mistake to avoid is treating the three SKUs as interchangeable line items; they are not, and a spec that swaps one for another without checking the plants-in-room and EPA rows is a spec that will fail at audit or in the room.

EPA and state compliance notes

Two of the three are EPA-registered: V at 87508-3-89334 and G at 87508-2-89334. D is not registered, and its disclaimer is verbatim: Not an EPA-registered product and not labeled for sale as a pesticide under 40 CFR. That is not a knock on D; it is the correct lane for an air-quality product that makes no kill claims and runs around a live crop. State cannabis rules layer on top of the federal EPA picture, so check your state's approved product list before you write SOPs, and read each product label in full before use. It is a violation of Federal Law to use a product in a manner inconsistent with its labeling.

How to choose, in one line

Surfaces with plants in the room is V. Empty-room reset is G. Air quality and odor with plants in the room, for up to 30 days, is D. Most established grows run all three across the cycle, because they answer three different jobs, not one. The question is never really which single product wins; it is which product fits the room in front of you right now. Once you have made the call, the product detail, labels, and SDS live on prokuresolutions.com, and reorders run through shop.groclarity.com. For a multi-room or multi-state program, GroClarity can scope the whole thing from a quote request.

Related resources