ProKure V vs ProKure G for room turnover: which ClO2 product does which job

You are standing in a stripped flower room deciding which ProKure product to open first, and the honest answer is usually both, in sequence. ProKure G is the fast-release gas that fumigates the whole empty room, including the air, the HVAC returns, the ceiling, and the surfaces a sprayer never reaches. ProKure V is the liquid disinfectant that then handles the hard surfaces crews and plants will actually touch: benches, trays, walls, floors, tools. The one-line rule is G for the room and its air, V for the surfaces. You run both, in order, whenever the prior cycle carried any pathogen pressure.

This page owns the workflow question, not the chemistry lecture. Below is the 60-second decision, what each product does in a turnover, how to sequence them across the turnover clock, the EPA facts a QA lead needs, and what each product cannot do alone.

The 60-second answer

ProKure V is the surface step. It is an EPA-registered liquid Hospital-Type Disinfectant (EPA Reg. No. 87508-3-89334) applied to hard, non-porous surfaces, residue-free when used per label, and suitable for use with plants in the room. In a turnover it handles benches, trays, tables, walls, floors, drains, and tools.

ProKure G is the whole-room step. It is an EPA-registered fast-release ClO2 gas (EPA Reg. No. 87508-2-89334) that fills the empty room volume and reaches the HVAC, ductwork, ceilings, and unreachable geometry a liquid cannot. It carries the verbatim label restriction "Not for use with/on plants/crops/feed," so it runs only in a cleared, empty room with no people, pets, or plants present during the dwell.

Use both when the prior cycle had any mold or mildew pressure at all: G first to reset the empty room and its air, then V to disinfect the surfaces once the room is vented and cleared for entry. Use V alone for a light, routine turnover with no pathogen history. Running G alone leaves the surfaces workers will touch unprotected against recontamination; running V alone leaves the air handler and the unreachable geometry untreated.

What ProKure V is, and the job it owns in a turnover

ProKure V is a water-activated liquid ClO2, an EPA-registered Hospital-Type Disinfectant. You drop the sealed inner pouch into an opaque container of cool water, do not open the inner pouch, agitate at intervals, and the solution reaches full strength at one hour. Then you apply it to hard, non-porous surfaces by sprayer, mop, or sponge, holding the labeled contact time.

In a room turnover, V owns the surfaces. It disinfects the benches, trays, tables, walls, floors, drain covers, and tools that the crew handles and that the next crop will sit on. For disinfection it runs at 100 ppm with a 10-minute contact time on hard non-porous surfaces, and it kills SARS-CoV-2 on hard non-porous surfaces in 30 seconds at 100 ppm. It leaves no residue when used per label, which is the exact difference a facility manager cares about after watching bleach or quats leave a film on a bench that then touches clones. It is suitable for use with plants in the room, so the surface pass does not force an evacuation the way a fumigant does. What V does not do is treat the air or reach into the HVAC, because it is a contact product applied to a surface, not a gas.

What ProKure G is, and the job it owns in a turnover

ProKure G is a water-activated fast-release ClO2 gas. You place the inner pouch in a dispersion cup with about 1.5 inches of water in a central location, and the deep-penetrating vapor fills the room over a 4-to-6-hour dwell. As a gas, it distributes through the entire room volume and reaches the HVAC returns, the ductwork, the ceiling, and the corners and voids a sprayer points past.

In a turnover, G owns the whole-room reset. It is the step that addresses the air handler and the unreachable geometry where spores from a prior powdery-mildew or Botrytis cycle hide. Because it works at a room-filling concentration, its label restricts it to an unoccupied space: "Not for use with/on plants/crops/feed." People, pets, and plants are out during the dwell, and you ventilate and turn the lights on for one hour before re-entry. Size the packet to the room by cubic feet (a 25g covers up to 2,250 cubic feet, a 10g up to 1,000), and run it on the empty room before the surface pass. What G does not do is stay on surfaces: the gas dissipates after it works, so it leaves no residual to catch recontamination from foot traffic, equipment reinstall, or clone introduction. That is the surface job, which is V's.

The room turnover SOP: V, G, or both

The right combination depends on what the prior cycle left behind.

For a routine turnover with no pathogen history, a V-first surface pass is often enough: strip the room, pre-clean soiled surfaces, disinfect with V, dry, inspect, re-plant. The air handler did not see a problem last cycle, so a full fumigation is not mandatory.

For a turnover after a positive mold or yeast test or visible IPM pressure, run G first, then V. The gas resets the empty room and the air handler that the surface pass cannot reach, and once the room is vented and cleared for entry, the V surface pass disinfects everything the crew and the next crop will touch. G addresses where the spores are hiding; V protects where the work happens.

For a turnover in a room that shares HVAC with adjacent rooms still in flower, G-first is effectively mandatory, because the shared air handler is the pathway a problem travels. Isolate the room from the shared return during the G dwell so you are not pushing treated or contaminated air into occupied rooms, then run the V surface pass. The shared duct is exactly why the whole-room gas step cannot be skipped in a multi-room facility.

The turnover clock, hour by hour

Facility managers lose 3 to 5 days per cycle to turnover, so the real comparison is on the clock, not the sticker price. A combined G-plus-V turnover maps onto the calendar cleanly. Day 0 is strip and gross clean. Day 1 is the G fumigation dwell, 4 to 6 hours of gas work in the sealed empty room followed by one hour of ventilation before re-entry. Day 2 is the V surface pass across benches, walls, floors, and tools, applied to visible wetness and held for the labeled contact time, then dried. Day 3 is dry, inspect, and air-test to confirm the reset. Day 4 the room is ready for clones.

That sequence can bring a thorough, documented turnover inside about four days, and because G works in hours rather than forcing a multi-day fume-and-air-out stall, it compresses the exact downtime a bleach-only protocol stretches out. The residue-free profile of both products is part of the speed: there is no long rinse step and no film to chase off a bench before the next crop sits on it.

EPA compliance and label restrictions

Compliance is the biggest single worry for operators at turnover, so keep the facts in plain sight. ProKure V is EPA Reg. No. 87508-3-89334, a liquid Hospital-Type Disinfectant with contact and dwell claims, suitable for use with plants in the room. ProKure G is EPA Reg. No. 87508-2-89334, a fast-release gas whose label carries the verbatim restriction "Not for use with/on plants/crops/feed," which is why it runs only in a cleared, empty room. Do not cross those labels: the plant restriction belongs to G, not V, and attaching it to the wrong product is the most common documentation error.

The governing federal language applies to both registered products: it is a violation of Federal Law to use an EPA-registered product in a manner inconsistent with its labeling, so read each label and run each product to it. State cannabis programs can add requirements on top of the federal label, so a multi-state operator should confirm each state's rules rather than assuming the EPA registration settles every question. Keep each product's label and SDS on file from prokuresolutions.com so the registration evidence is in the audit binder before an inspection, matched to the correct product.

PPE, crew safety, and what each cannot do

The crew-safety profiles differ, and that difference drives the SOP. V is a surface application: standard spray PPE, minimal off-gassing, and no room evacuation to run it, which is why it is the plants-present surface tool. G is a room fumigant: the room is sealed and evacuated during the dwell, and re-entry follows ventilation and, for a documented SOP, an air check to confirm clearance. Build the sequence so the gas step happens while the room is empty and the surface step happens after it is cleared.

Each product has a failure mode alone. V alone misses the HVAC, coils, ductwork, ceilings, and any porous or unreachable surface a spray cannot cover, so if the prior cycle had powdery mildew or Botrytis, the spores in the air handler survive a surface-only pass. G alone leaves no residual, so anything that recontaminates the room during equipment reinstall, worker foot traffic, or clone introduction lands on surfaces the dissipated gas no longer protects. The reason the combined SOP exists is that each product covers the other's blind spot.

Proving the turnover worked

A turnover you cannot document is a turnover an auditor will not credit, and a head grower needs that proof. Pull an air-quality baseline before the turnover, verify after, and log the results per room alongside the treatment record: product, SKU, room, date, operator, dwell and ventilation times, and the air-test results that bracket the reset. That data trail ties the SOP to the state pre-sale yeast and mold thresholds the crop will be tested against, and it is the evidence that turns a claimed program into one an inspector can follow. GroClarity supports building that air-quality data trail, which is the piece the empty search results leave entirely to the grower.

Cost and where to buy

Model cost per room per turnover, not cost per bottle. A V-only turnover is the mixed solution volume plus the labor to apply, dwell, and dry. A G-only turnover is the packet count sized to room volume plus low application labor. A combined SOP is both, and for a room coming off pathogen pressure it is the cheaper outcome once you weigh it against a failed yeast-and-mold test on a mature crop, where the prevention math is not close. Rather than publish figures that mislead across room sizes, price your real per-room cost on shop.groclarity.com for the SKUs your rooms call for, and request a quote for facility-scale and account pricing. Order ProKure V and ProKure G on shop.groclarity.com, pull labels and SDS from prokuresolutions.com, and reach a GroClarity rep to standardize a V-plus-G turnover SOP across multiple rooms or states.

Related resources

Related resources