The short answer

ProKure G and ProKure D are not substitutes, they are a sequence. ProKure G is the fast-release gas: it deep-cleans an empty room in 4 to 6 hours, and because it carries the required label disclaimer Not for use with/on plants/crops/feed, it runs only when the plants are out. ProKure D is the slow-release gas: it provides ClO2 protection for up to 30 days, improves air quality and controls odors, and it runs with plants in the room, trifolds hung above the canopy. Most commercial operations use both, G for the between-cycle reset, D for the ongoing air across the grow. The decision below is really about duration and occupancy.

What each product is

ProKure G is a fast-release gas deodorizing delivery system, EPA Reg. No. 87508-2-89334. Its approved job, in ProKure's own language, is the solution for mold and mildew, odor-causing bacteria, and chemical odors, a deep clean between harvests that works in 4 to 6 hours with deep-penetrating ClO2 vapor. It is a registered product, so label-consistent use is federal law.

ProKure D is a slow-release gas that provides ClO2 protection for up to 30 days and improves air quality and controls odors. It is not an EPA-registered product and not labeled for sale as a pesticide under 40 CFR, so it makes no kill claim and is an air-quality measure rather than a pesticide. That non-registered status is exactly why D can run with plants present where G cannot. Ignore any reseller framing that calls D an unoccupied-room product; the approved claim is air quality with plants in the room, trifolds hung 18 to 24 inches above the canopy.

Side-by-side differences

The comparison table lays out the two axes that decide this, duration and occupancy, plus the EPA status a QA lead needs. In short: G is hours and an empty room; D is up to 30 days and a live canopy. G is EPA-registered with a plants-crops-feed restriction; D is non-registered with the 40 CFR disclaimer. Their coverage SKUs differ too, which is how you size the dose to the room volume.

When to use ProKure G

Reach for G when the room is empty and the job is a reset: a deep clean between harvests, an acute odor event, or a chemical and VOC odor knock-down before the next crop goes in. Activate per the label, allow at least 4 to 6 hours for the system to work, and ventilate before re-entry. The hard rule that governs every G deployment is the verbatim disclaimer Not for use with/on plants/crops/feed, so G never runs with a canopy in the room. If your actual job is surface disinfection rather than air, that is a different product: ProKure V is the EPA-registered liquid for hard, non-porous surfaces and is suitable for use with plants in the room.

When to use ProKure D

Reach for D once the room is back in production and you want to hold air quality across the cycle. D provides ClO2 protection for up to 30 days and improves air quality and controls odors, running with plants present. Keep the up to qualifier: 30 days is the ceiling of the release window, not a flat month, and there is no official 50/50 or every-two-weeks rotation schedule, so replace each pouch before its up-to-30-day window closes and size the pouch count to the room rather than assuming a fixed cadence the label does not state. D carries the verbatim disclaimer Not an EPA-registered product and not labeled for sale as a pesticide under 40 CFR, and it makes no kill claim.

Do you need both?

Usually, yes, in sequence. The common commercial workflow is G for the between-cycle reset in the empty room, 4 to 6 hours of deep-penetrating vapor to knock down odor and reset the air, then D once plants are back in, hung above the canopy for up to 30 days of ongoing air quality. They are complements: G handles the acute empty-room event, D handles the chronic in-room maintenance. Buying one without the other leaves half the cycle uncovered. For air quality management across a live canopy, D is the tool; for the empty-room reset, G is.

Pricing context

Both products are sized by coverage, so cost tracks room volume and cycle cadence, not a flat sticker. ProKure G comes in a 25g pouch (about 2,250 cubic feet for standard odors, 1,000 for heavy) and a 10g pouch (about 1,000 cubic feet standard, 500 heavy), and each use is a single activation. ProKure D comes in 95g (about 8,000 cubic feet), 50g (about 4,000 cubic feet), and 10g (about 1,000 cubic feet), with a reusable trifold, replaced before each pouch's up-to-30-day window closes. Size the SKU to your room, count the D replacements across a cycle, and treat the combined cost as a recurring air-quality line against the loss of a failed yeast-and-mold test. Current per-SKU pricing is published on shop.groclarity.com so you always see the live number.

Dr. B's recommendation

If you run a repeatable cycle, stop treating this as an either-or. Buy G for the turnover and D for the grow, and run them in that order. The single most common mistake is reaching for one gas and expecting it to do both jobs: G cannot stay in a room with plants, and D is not a fast empty-room reset or a kill-claim product. Match the product to the moment, empty-room reset or in-room maintenance, and keep each disclaimer on its own product. When you need surface work too, add ProKure V for the hard, non-porous surfaces.

Frequently asked questions

The questions below are the ones buyers actually raise when choosing between the two gases.

Related resources

Related resources