Botrytis vs Powdery Mildew on Cannabis: How to Tell Them Apart and Which Prevention Protocol You Actually Need
If you spotted something and cannot name it yet, start here. Botrytis, gray mold or bud rot, grows as a grey-brown fuzz inside dense buds in late flower and is driven by trapped humidity in the cola interior. Powdery mildew (WPM) is a white, powdery-sugar dusting on leaf surfaces that spreads canopy-wide from veg through early flower. Different organism, different location, different risk window. The identification decides the protocol: botrytis is a late-flower humidity fight, powdery mildew is a veg-stage airflow and surface fight, and both end at a clean between-cycle room reset.
If you already know which one you have
This page resolves identification and routes you. If you have already confirmed botrytis, the prevention detail lives in our mold prevention protocols pillar. If you have confirmed powdery mildew, the same pillar carries the veg-stage inspection cadence. Either way, the between-cycle room reset runs through cultivation IPM expertise. Use the table below only if you still are not sure which pathogen you are looking at.
The 60-second diagnostic: which one do I have?
Two questions resolve most cases. Where is it, and what does it look like? Botrytis hides inside the densest part of a cola and reads as grey or brown fuzzy rot, often with a grey-leaf early warning where foliage inside the bud dies back. Powdery mildew sits on top of leaves in the open canopy as a white dust you can sometimes wipe, and it is visible long before it reaches the flower. Botrytis is a late-flower problem; powdery mildew shows up in veg and early flower.
Side-by-side: botrytis and powdery mildew on cannabis
The diagnostic table that ships with this page lines the two up on the dimensions that resolve identification: scientific name, visual signature, location on the plant, risk window, environmental driver, and first triage action. The short version: botrytis is Botrytis cinerea, an interior bud rot driven by high humidity; powdery mildew is a surface fungus driven by moderate humidity with poor airflow. Confusing the two sends you to the wrong prevention lever, which is why the identification comes first.
Botrytis in cannabis: an interior humidity problem
Botrytis cinerea colonizes the inside of dense flowers where moisture collects and air does not move. By the time the grey-brown rot is visible on the surface of a cola, it has usually been working inside for days. The early tell is a single discolored or dying leaf buried in an otherwise healthy bud.
The risk window is late flower, roughly weeks six through ten, when the buds are densest and the plant is transpiring into a closing canopy. The prevention lever that matters most is humidity: drive late-flower relative humidity down, keep air moving through the canopy rather than just over it, and open dense colas with timed defoliation so the interior can breathe. Botrytis is a humidity fight you win with climate control and airflow, not with a surface spray on an already-rotting bud.
Powdery mildew in cannabis: a surface and airflow problem
Powdery mildew behaves nothing like botrytis. It is a surface fungus that establishes on leaves in the open canopy and spreads room-wide on air currents and handling. It shows up in veg and early flower, well before botrytis becomes a risk, and it moves between plants fast once it has a foothold.
The prevention levers are moderate humidity and strong airflow: keep relative humidity down, run oscillating fans to break the still-air boundary layer on leaf surfaces, space and prune plants so air reaches every leaf, and inspect new plants before they enter the room. Where botrytis is an interior-moisture problem, powdery mildew is a surface-and-circulation problem, and the veg-stage inspection cadence is the frontline defense.
Environmental controls and facility sanitation that cover both
Two things help against both pathogens: a humidity program tuned by growth stage, and a clean room between cycles. On humidity, run higher in veg and step down into flower, keeping the late-flower canopy on the dry side. On airflow, keep air moving through the canopy at every stage. Those two habits cut the pressure for both organisms at once.
The between-cycle reset is where chemistry comes in, and the product depends on whether plants are in the room. For surface disinfection, ProKure V is the liquid hospital-type disinfectant, EPA Reg. No. 87508-3-89334; it kills mold and mildew, leaves no residue with no wipe and no rinse, and is suitable for use with plants in the room, which is exactly why it replaces a bleach-and-quat rotation that cannot touch plant-adjacent surfaces. For a fast air reset in the empty room, ProKure G is a fast-release gas, EPA Reg. No. 87508-2-89334, that works in 4 to 6 hours and carries the verbatim label disclaimer Not for use with/on plants/crops/feed, so it runs only with plants out. For ongoing ambient air quality, ProKure D is a slow-release gas that provides ClO2 protection for up to 30 days; it is not an EPA-registered product and not labeled for sale as a pesticide under 40 CFR, so it is an air-quality and odor measure with no kill claim. Keep each disclaimer on its own product.
Dr. B recommendation: triage, then protocol
Identify first, then commit to the matching lever. If it is botrytis, the win is a dry, well-circulated late-flower canopy, and no surface product saves a bud already rotting from the inside. If it is powdery mildew, the win is early veg-stage detection plus airflow, because it spreads before it reaches the flower. In both cases, close the loop with a residue-free ProKure V surface reset between cycles so you do not carry spore load into the next batch. State pre-sale yeast-and-mold thresholds vary, so confirm yours with your regulator; both pathogens can drive a failed finished-flower test, which is the reason prevention beats triage.
Frequently asked questions
What are the differences between powdery mildew and Botrytis?
Powdery mildew is a white, powdery surface fungus on leaves in the open canopy that spreads room-wide in veg and early flower. Botrytis is a grey-brown rot that grows inside dense buds in late flower, driven by trapped humidity. Different organism, different location, different risk window: powdery mildew is a surface-and-airflow problem, botrytis is an interior-humidity problem.
What kills powdery mildew on cannabis?
On surfaces and in the room, an EPA-registered disinfectant like ProKure V kills mold and mildew and leaves no residue, and it is suitable for use with plants in the room. On the living canopy, the real control is prevention: lower humidity, strong airflow, plant spacing, and veg-stage inspection, because a surface treatment does not undo an active systemic infection. Reset the room between cycles so spore load does not carry over.
What are the best things you can do to prevent Botrytis?
Drive late-flower humidity down, move air through the canopy rather than just over it, and open dense colas with timed defoliation so the bud interior can breathe. Watch weeks six through ten, inspect the densest colas first, and pull any bud showing a grey interior leaf. Finish each cycle with a residue-free ProKure V surface reset in the room so the next batch starts clean.
Is there a way to prevent powdery mildew?
Yes. Keep relative humidity moderate, run oscillating fans to break the still-air layer on leaf surfaces, space and prune for airflow, and inspect every new plant before it enters the room, since powdery mildew usually arrives on an introduction. Between cycles, disinfect surfaces with a residue-free, EPA-registered option like ProKure V to clear spore load before the next crop.
Related resources


